manualshive.com logo in svg

lynx System Developers LaserLynx, Быстрый старт, Страница: 1 / 7

Поделиться
Скачать
lynx System Developers LaserLynx Скачать руководство пользователя страница 1

 

www.finishlynx.com 

 

Page 

1

 of 

7

 

 

 

L

YNX 

S

YSTEM 

D

EVELOPERS

,

 

I

NC

. 

 

LaserLynx

 

Quick Start Guide 

 

Verify that your LaserLynx system contains the components pictured below. 

If not, or if you need additional help, please call: USA 978.556.9780 or email 

[email protected]

 

 

Item 

Description 

ID 

 

Item 

Description 

ID 

 

Tripod 

TS50F 

 

 

USB-Serial 

adapter 

USB-

Serial1 

 

Target pole 

PC21 

 

 

Sighting unit 

6L209 

 

Prismatic 

reflector 

MPU1 

 

 

Battery 

Charger 

N/A 

 

Serial Cable 

S50660 

 

 

Battery 

S62005 

 

Items not included 

Computer (laptop or tablet recommended) running FieldLynx on Microsoft Windows. Your computer needs: one 
available serial port or USB port with a USB-Serial adapter. 

 

Introduction  

The following guide will walk you through the installation, setup and operations of LaserLynx. If at any point you 
need additional help, please contact Tech Support: 

[email protected].

 

Step 1 

Installation 

The LaserLynx plug-in should be installed on a computer with the latest version of FieldLynx or FieldLynx Lite. 

a.  Locate the LaserLynx installer (FLLaser #.##.exe) from the Lynx USB drive.  

b.  Right-click on the installer and click 

Run as Administrator

.

 

c.  Follow the prompts to complete the install. 

Содержание LaserLynx








Отзывы:

Нет отзывов