LXE MX7 Скачать руководство пользователя страница 10

Страница: 10 / 60

Desktop Cradle LEDs

MX7 Cradle Reference Guide

E-EQ-MX7DKRG-C

Desktop Cradle LEDs

Figure 4 Desktop Cradle Front Label

MX7 Docked LED

When Docked LED is …

It means ….

Off

MX7 not inserted or no power applied

Red

MX7 docked and power applied.

The cradle must be connected to AC power.

Spare Battery LED

When Spare LED is …

It means ….

Off

Battery pack not inserted or no power applied

Green

Battery pack fully charged

Red

Battery pack charging

Yellow / Amber

Battery pack temperature out of range

Flashing Red

Battery pack fault or failure

The cradle must be connected to AC power. This process does not require an MX7 be in the
docking bay.

MX7 Mobile Device System Status LED

The MX7 System Status LED is located at the top left of the keypad, above the Scan button.

When the LED is . . .

The Status is . . .

Comment

Blinking Red

Power Fail

Replace the main battery with a fully charged
main battery.
Or
Connect the MX7 to external AC power to
allow the internal charger to charge the main
battery e.g. dock in a powered cradle.

Steady Red

Main Battery Low

Low Battery Warning. Replace the main
battery with a fully charged main battery. Or
dock the MX7 in a powered cradle.

Blinking Green

Display Off

No user intervention required.

No Color

Good

No user intervention required.

Note:

The Passive Vehicle Cradle does not have LEDs.

Содержание MX7




























































Результаты поиска

Содержание MX7

Отзывы:

Бренды по названию

Популярные бренды

LXE MX7, Справочное руководство

Результаты поиска

Содержание MX7

Отзывы:

Бренды по названию

Популярные бренды