LXE MX1-IS Скачать руководство пользователя

Страница: 50 / 164

Installed Software

MX1 I-Safe Reference Guide

E-EQ-MX1ISRG-F

Radio-Specific Subdirectory

\PCTCP (2.4GHz Radio Specific
Files)

The PCTCP files are included with MX1-IS’s that have a 2.4 GHz radio installed.

DRIVER.1ST

Radio driver file.

IPSTAT.EXE

Gives statistics on IP and memory.

LSL.COM

Link Support Layer driver.

NET.CFG

Contains radio parameters.

ODIPKT.COM

ODI Packet driver.

PDTEST.EXE

Test or diagnose the packet driver.

SETHOST.EXE

Manage host names and IP addresses.

SOCKET.CFG

Contains options for SOCKETP.EXE

SOCKETP.EXE

Sockets TCP/IP kernel for use with packet drivers.

TCP.EXE

Manipulate or view TCP parameters and status.

WVLAN43.*

Lucent radio driver files.

XPING.EXE

Test installation with a continuous ping.

LXE 900MHz Radio Files

The LXE 900MHz radio files are installed in the Terminal Emulation subdirectories.

LXE900SS.EXE

Spread spectrum radio driver.

LXE900SS.HEX

Modem control codes.

PCRFLIB.EXE

Interface between the radio driver and the terminal emulator.

RFPARSE.EXE

Used by PCRFLIB to obtain configuration settings.

Содержание MX1-IS





































































































































































Результаты поиска

Содержание MX1-IS

Отзывы:

Похожие инструкции для MX1-IS

Бренды по названию

Популярные бренды

LXE MX1-IS, Справочное руководство

Результаты поиска

Содержание MX1-IS

Отзывы:

Похожие инструкции для MX1-IS

Бренды по названию

Популярные бренды