LXE MX1-IS Скачать руководство пользователя

Страница: 18 / 164

Adjust Display and Volume

MX1 I-Safe Reference Guide

E-EQ-MX1ISRG-F

Adjust Display and Volume

Set The Display Contrast

Adjusting screen contrast lightens or darkens the characters on the screen to make them visible at
a comfortable level. The contrast is incremented or decremented one step each time the contrast
key is pressed.

Full Alpha-Numeric

The full alpha-numeric keypad does not have a contrast key legend. Adjust the display contrast by
pressing the:

•

key, then the Shft key then the <C> key to enter Contrast change mode.

•

Use the Up Arrow and Down Arrow keys to adjust contrast until the display lightens or
darkens to your satisfaction.

Press the Enter key to exit this mode.

Numeric-Alpha Keypad

To adjust screen contrast, locate the <F11> key at the bottom of the keypad. Adjust the

display contrast by pressing the:

•

key, then the <F11> key

•

Use the Up Arrow and Down Arrow keys to adjust contrast until the display lightens or
darkens to your satisfaction.

Press the Enter key to exit this mode.

Содержание MX1-IS





































































































































































Результаты поиска

Содержание MX1-IS

Отзывы:

Похожие инструкции для MX1-IS

Бренды по названию

Популярные бренды

LXE MX1-IS, Справочное руководство

Результаты поиска

Содержание MX1-IS

Отзывы:

Похожие инструкции для MX1-IS

Бренды по названию

Популярные бренды