LXE MX1-IS Скачать руководство пользователя | Manualshive

Страница: 14 / 164

background image

4

Getting Started

MX1 I-Safe Reference Guide

E-EQ-MX1ISRG-F

Getting Started

When your MX1-IS is pre-configured, the radio card and endcap are assembled
by LXE to your specifications. At the end of the manufacturing process, the
contents of the MX1-IS are sealed. Access to any internal components by the
user is inhibited.

This section’s instructions are based on the assumption that your new system is pre-configured
and requires only a power source.

In general, the sequence of events is:

1.

Insert a fully charged Main Battery Pack.

2.

Power the MX1-IS on.

3.

Configure the software.

Note:

New batteries must be fully charged prior to use

. This process takes approximately three

hours per battery. MXI-IS batteries are charged using the LXE MX1-IS MULTI-charger.

Refer to the documentation received with the MULTI-charger for operating
instruction and technical information.

If you need to set up the integrated scanner

barcode reading parameters

, please

refer to the “

Integrated Scanner Programming Guide

” on the LXE Manuals CD or

the LXE website www.lxe.com.

Important

– LXE manufactures a device physically similar to the MX1 Intrinsically Safe

Hand Held Computer (MX1-IS). Do not place MX1-IS Main Battery Packs in any battery
charging device not specifically designed for the MX1-IS battery pack. Also, the MX1-IS
device is not compatible with the LXE MX1 Main Battery Packs.

«
...
12
13
14
15
16
...
»

Содержание MX1-IS





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX1-IS

Toughbook CF-P1 Series

Бренд: Panasonic Страницы: 42

Бренд: Motorola Страницы: 3

Бренд: Motorola Страницы: 5

Бренд: Motorola Страницы: 98

Бренд: Motorola Страницы: 160

Бренд: Motorola Страницы: 2

Бренд: Motorola Страницы: 2

Бренд: Motorola Страницы: 206

Бренд: Motorola Страницы: 166

Бренд: Motorola Страницы: 350

Бренд: Motorola Страницы: 136

Бренд: Motorola Страницы: 88

MC55 - Enterprise Digital Assistant

Бренд: Motorola Страницы: 245

Бренд: Partner Страницы: 37

Бренд: Palm Страницы: 2

$Datalogic Kyman\ User Manual preview$

Бренд: Datalogic Страницы: 117

Бренд: ACD Страницы: 16

Бренд: PDi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды