LXE E-SW-BLUESCANPG-B Скачать руководство пользователя страница 38

Страница: 38 / 308

Introduction

Bluetooth Ring Scanner Guide

E-SW-BLUESCANPG-B

Bluetooth Module Technical Specifications

Physical

I/O Port

A 22 spring-pin, symmetrical port

Module Size

Without Scanner : Height 0.75” / 1.90cm x Width 1.75” /
4.44cm x Length 2.4” / 6.1cm

With Scanner : Height 0.75” / 1.90cm x Width 1.75” /
4.44cm x Length 2.9” / 7.4cm

Module Weight

2.15oz / 60.9g with battery / 1.60oz / 45g without battery

4.05 – 4.15oz / 114g – 117g with battery and scanner

Ring Scanner : 1.75oz / 49.6g

Ring Imager : 1.85oz / 52.4g

Environmental

Operating Temperature

-4° F to 122° F (-20° C to +50° C)

Storage Temperature

-40° F to 158° F (-40°C to +60°C)

Water and Dust Resistance

Sealed to IP-54 specifications or better

Humidity

5% to 95% relative humidity, non-condensing

Corrosion

Corrosion resistant when exposed to water and common
cleaning chemicals

Chemical Resistance

Corrosion resistant when exposed to water and common
cleaning chemicals

Abrasion Resistance

Housing resists normal abrasion from dirty hands.

The CF Bluetooth Radio in the LXE Bluetooth Ring Scanner is Bluetooth Special Interest Group
(SIG) Qualified, is listed as an EPL (End Product Listing) and with QDID: B011904.

Содержание E-SW-BLUESCANPG-B





















































































































































































































































































































Результаты поиска

Содержание E-SW-BLUESCANPG-B

Отзывы:

LXE E-SW-BLUESCANPG-B, Руководство пользователя, Страница: 38 / 308

Результаты поиска

Содержание E-SW-BLUESCANPG-B

Отзывы: