LXE E-SW-BLUESCANPG-B Скачать руководство пользователя страница 253 | Manualshive

Страница: 253 / 308

LXE E-SW-BLUESCANPG-B Скачать руководство пользователя страница 253

SE4400 Imager Barcodes

241

E-SW-BLUESCANPG-B

Bluetooth Ring Scanner Guide

MSI

Parameter Default Value:

Disable

When enabled, MSI symbols will be scanned, decoded and transmitted.

Set this parameter by scanning either of the barcodes shown below.

Enable MSI

Disable MSI

Set Length(s) for MSI

Length Within Range

L1 Parameter Default Value: 04

L2 Parameter Default Value: 55

Lengths for MSI may be set for:

•

any length,

•

one or two discrete lengths,

•

or lengths within a specific range.

The length of a code refers to the number of characters, including check digits, the code contains.

Note: Due to the construction of the MSI symbology, it is possible for a scan line covering only

a portion of the code to be interpreted as a complete scan, yielding less data than is
encoded in the barcode. To prevent this, select specific lengths (using MSI One Discrete
Length and MSI Two Discrete Lengths) for MSI applications.

See the table titled “ASCII Character Equivalents” at the end of the “Appendix”.

«
...
251
252
253
254
255
...
»

Содержание E-SW-BLUESCANPG-B





















































































































































































































































































































Отзывы:

Нет отзывов