manualshive.com logo in svg

LXE E-SW-BLUESCANPG-B, Руководство пользователя, Страница: 107 / 308

Поделиться
Скачать
LXE E-SW-BLUESCANPG-B Скачать руководство пользователя страница 107

SE955 Laser Barcodes 

95 

E-SW-BLUESCANPG-B 

Bluetooth Ring Scanner Guide 

Software Handshaking 

Default Value  Enable 

This parameter offers control of the data transmission process in addition to that offered by 
hardware handshaking.  

Hardware handshaking is always enabled and cannot be disabled by the user. 

Scan one of the following barcodes to set software handshaking. 

Disable ACK/NAK Handshaking 

When this option is selected, the decoder will neither generate nor expect ACK/NAK handshaking 
packets. 

 

Enable ACK/NAK Handshaking 

When this option is selected, after transmitting data, the scanner expects either an ACK or NAK 
response from the host. The scanner will also ACK or NAK messages from the host when this 
option is selected. 

The scanner waits up to the programmable Host Serial Response Time-out to receive an ACK or 
NAK. If the scanner does not get a response in this time, it resends its data up to two times before 
discarding the data and declaring a transmit error.  

 

 

Содержание E-SW-BLUESCANPG-B





















































































































































































































































































































Отзывы:

Нет отзывов