LX Navigation Era 57 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 98

LX Navigation Era 57 Скачать руководство пользователя страница 66

LX Era

Device setup

Document name:

LX EUM

Document revision:

R1

5.2.4

Inputs

The Input setup sub-menu refers to the functionalities of the Era closely dependant on
existence and proper use of the Inputs interface. The inputs interface incorporates slots for
5 external micro-switches, connected to the Input port on the Era. These micro-switches can
trigger different functions and commands, as well as warnings.

The following functions are available:

•

SC -

when assigned and triggered, will change the current ﬂight mode. Check

Flight mode

sub-section for additional info.

•

VP -

changes to vario ﬂight mode, no matter which settings are active

•

event -

triggers the event functions, check

section for additional info.

•

gear -

if any of the two gear inputs is selected (straight or inverse), the gear warning will

be applied in the following sense:

–

gear is out detected 10min after take-off and height more than 500m above take-off
location.

–

gear is not out and altitude is less than 200m in 5km circle of take-off location and
ﬂight time is more than 5min.

–

on outlanding (if airbrakes are out, elevation less than 600m QFE, distance from
take-off more than 5km), and gear is not out. Requires the airbrakes switch to be
used.

•

airbrake -

if any airbrake is selected (straight or inverse) gear warning will be announced

as follows:

–

airbrake is out during ﬁrst 10min of ﬂight (take-off / aero tow time).

•

ballast -

triggers the ballast dump rate function, as depicted in

sub-section.

The Input page requires the use of the

Inputs interface

, shipped along with the Era. We can

see the inputs interface on the picture below.

Figure 72.

NOTE

All input functions have an inverse function as well. Having a straight function will

trigger once the button has been pressed. Utilizing an inverse function will trigger

once the button has been released (useful for air brakes, etc.).

Device manual

Public

66

«
...
64
65
66
67
68
...
»

Содержание Era 57



































































































Отзывы:

Нет отзывов