LX Navigation Era 57 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 98

LX Navigation Era 57 Скачать руководство пользователя страница 33

LX Era

Advanced operation

Document name:

LX EUM

Document revision:

R1

4.5

Airport navigation page

This page is intended exclusively for navigating towards a single airport, from the .af ﬁle loaded
into the Era. The navigation screen shows turnpoints, airports and airspaces on the map area.

The Airport navigation page is set up in much the same way as the

Turnpoint navigation page

so be sure to check the previous section for additional information.

The layout of the Airport navigation page is identical to the Turnpoint navigation page. At the
top, we have

APT

written, noting the page we’re currently on, and the name of the chosen

airport immediately below.

Below the name of the select airport is the steering course (relative bearing). All of the
mentioned parameters form the header of the navigation page, shared across all navigation
pages.

Figure 39. Airport navigation page overview

Below the central map display, the same NavBoxes are used as with the Turnpoint navigation
page, forming the footer of the navigation page, also shared across all navigation pages.

Pressing the upper push-rotary knob will open the APT info page, showing Bearing, Distance,
Frequency, Final glide, Elevation and Runway direction.

Pressing the lower push-rotary knob, you will enter the ’Select airport’ sub-page. Here, a
selection of airports will be shown, along with distance and bearing, as well as steering course
(relative bearing) as described earlier, with an arrow. These points can be sorted by either
Distance, Name, or ICAO code.

Device manual

Public

33

«
...
31
32
33
34
35
...
»

Содержание Era 57



































































































Отзывы:

Нет отзывов