LX Navigation Era 57 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 98

LX Navigation Era 57 Скачать руководство пользователя страница 16

LX Era

Basic operation

Document name:

LX EUM

Document revision:

R1

Once you have received the update code, follow these steps:

1. Copy the desired software update to the root of the microSD card. The update ﬁle should

have the word Era within its name and an extension of .lxu

2. Turn the device on and insert the microSD card
3. Go to

Setup

>

Service

>

Software update

4. Select the desired update ﬁle
5. When prompted, type in the update code supplied by LX support
6. The device will copy the ﬁle to the internal memory and perform the update. It may restart

a couple of times.

7. Once the update has ﬁnished, verify that the update has been successful by going to

Setup

>

Service

>

Device info

and checking that the SW version has changed to the

desired one

NOTE

While the Zeus version of the Era will restart automatically, a standalone Era

requires the bottom push-rotary knob to be pressed in order to turn them on, after

the ﬁle has been copied, for the updating process to proceed.

WARNING

Once the Era has been updated, it will update all CAN-compatible devices (LX

Joy, second seat device, etc). For this reason, the Era should be left ON for at

least ﬁve minutes after the main unit has been successfully updated. If the

update of CAN units is ongoing, an infobox will appear, notifying the pilot.

WARNING

Great care should be taken not to turn the device off while the updating process

is running. Data corruption may occur. If something similar happens, contact LX

support immediately, in order to recover you unit.

3.5

Turning the Era off

The Era can be turned off in different ways, depending on the conﬁguration you have.

All units will start the shutdown process once the power supply is cut from the main power
lines or the CAN bus, the latter representing a shutdown of the Zeus, unless in ﬂight mode.

There is a possibility of a manual shutdown by going to

Setup

>

Shutdown

and conﬁrming by

choosing ’Yes’.

In case a device requires a force shutdown,

there is a possibility of performing a hard

shutdown by pressing and holding the PAGES push-rotary knob for 10 seconds

.

Device manual

Public

16

«
...
14
15
16
17
18
...
»

Содержание Era 57



































































































Отзывы:

Нет отзывов