LV switch SIP-T780 Скачать руководство пользователя страница 36

Страница: 36 / 117

SIP-T780 IP Phone User Manual

4.2 Voice setting

There are several sound settings in T780, including the following

points：



Volume setting



Ringtone setting



Button voice setting



Signal tones setting

4.2.1 Volume setting

The T780 phone can set the ring volume and the volume during the call.

The volume setting range is 1-15, and the volume becomes larger as the

value increases.

- Set the ring volume of incoming calls in standby/ringing state

1. Press

to adjust the ring volume，as the diagram:

- Set the volume of the handset, speaker headset and other devices when

a call comes in

1. Press

adjust call volume，as the diagram shows:

4.2.2 Ringtone setting

You can set different ringtones for your phone to distinguish incoming

calls. In addition to unified ringtones, contacts can also set different

ringtones to distinguish incoming calls from different contacts. The

system provides a total of 10 default ringtones to choose from.

Содержание SIP-T780






















































































































Результаты поиска

Содержание SIP-T780

Отзывы:

Похожие инструкции для SIP-T780

Бренды по названию

Популярные бренды

LV switch SIP-T780, Руководство пользователя

Результаты поиска

Содержание SIP-T780

Отзывы:

Похожие инструкции для SIP-T780

Бренды по названию

Популярные бренды