LV switch IPPBX3000 Скачать руководство пользователя

Страница: 52 / 195

LvSwitch IPPBX 3000 Manual

Figure5- 13 Static Route

Add route configuration description

：

Table 5- 5 Add Routing

Item

Description

Name

User defined route name.

Destination IP

The destination address need to reach, it could be network
address or host address.

Gateway

The IP address of the next router to pass before the data
reaches the destination address.

NetMask

The destination address subnet mask to be reached.

Network Type

Select the static route out interface, including the LAN port
and WAN port.

5.2.3 Dynamic route

Dynamic routing means that the router can automatically set up its own routing table and adjust it according

to the actual situation. The routing information exchange between the product and the docking device is realized
based on RIP routing protocol. Route: network >advanced options>dynamic route, the page pops up as following:

Содержание IPPBX3000




































































































































































































Результаты поиска

Содержание IPPBX3000

Отзывы:

Похожие инструкции для IPPBX3000

Бренды по названию

Популярные бренды

LV switch IPPBX3000, Руководство пользователя

Результаты поиска

Содержание IPPBX3000

Отзывы:

Похожие инструкции для IPPBX3000

Бренды по названию

Популярные бренды