VIDEO: The smaller, the slower, it may adjust the potentiometer of lens.
AI THRESH: Auto-iris lens switching point. Larger than the threshold, electron-
ic shutter works, lower than the threshold, Al works. The default is -18.
- SYNC
Use line synchronization to eliminate
the vertical roll that occurs when
multiple cameras are connected to
the same switching device. Line lock:
Select LINE LOCK to manually set the
vertical phase for this camera.
The range is from 0 to 624. The default is 519.
2.3. EXPOSURE
- WHITE BALANCE:
It is especially effective in scenes with changing color temperatures.
ATW: Select this option for constant lighting scenes, such as indoor applica-
tions.
ADV ATW: Continuously calculates
white balance settings and dynami-
cally adjusts for changing conditions.
The range is from 2000° K to11000° K.
AWB: Renders the most possible ac-
curate image color. Mixed color,
applications may affect the color
adjustment.
For example, a small white object on
a large blue surface may have a red-
dish tint.
AWB uses a calibration image to identify the correct white level. The cam-
era then uses this white level when adjusting overall image color.
VR480
Color Camera
Day/Night
Wide dynamics
1. SETUP BOARD
1.1. Signal Switch
“X1” (default setting) is the switch for single video output; the vid-
eo can be carried either from the video connector of OSD Control
Panel or Dome Camera. “X2” is dual video outputs for both OSD
Control Panel and Dome Camera. When using only one video
output, please switch to “X1” for appropriate video image. When
using two video outputs, please switch to “X2” for appropriate vid-
eo image. Please follow these instructions to avoid any damages
or dangers.
1.2. Power Input Terminal
Connect the power supply of 12Vdc. 12Vdc power supply can be
connected to this terminal or the camera’s power input terminal.
Please only connect to one power supply to avoid any damages
or dangers.
After the functions setting is completed, please remove the OSD Con-
trol Panel from the Dome Camera.
1.3. Key
Use center button to enter menu or select a menu.
Press it for 2 seconds, the menu will appear, con-
tinuous press on the key to exit.
Move the icon vertically between the menus and
options.
Move the icon horizontally between the menus and
options
2. MENU FUNCTIONS
2.1. PRESET MODE
Select default NORMAL/ INDOOR/OUTDOOR/ FLUOR1/ FLUOR2/ CUSTOM
modes with left and right key.
NORMAL: Mainly use for stable lighting environments.
INDOOR: Mainly aim from indoor to outdoors.
OUTDOOR: Mainly use for outdoors.
FLUOR1: Optimized for indoor use with fluorescent lights, maintains HDR with at
normal light levels. The sync choice for line lock is 60.01hHz or 59.97Hz.
FLUOR2: Optimized for indoor use with fluorescent lights, prevents flicker with
-
out requiring line lock, fixed 2x ESS with normal dynamic range.
CUSTOM: Customize the image effect
2.2. BASIC SETUP
- LANGUAGE:
Select the language type of the menu with left, right key. Chi-
nese and English optional.
- VIDEO I/O
VIDEO STANDARD: The camera supports both NTSC and PAL video stan-
dards.
VIDEO LEVEL: Set the video output
voltage from 1.0 Vp-p to 1.2 Vp-p.
You can use it to boost the video
output to compensate for signal loss
due to long cable runs. 100 ~ 120
corresponds to 1.0 ~ 1.2Vp-p. The de-
fault is 110.
COLOR BAR: Adjusts the color, resolution or brightness.
MIRROR: Select ON to mirror the image horizontally. The default is OFF.
1
3
2
4
VR480-Manuel-V02
MAIN MENU
PRESETS
BASIC SETUP...
EXPOSURE...
ADVANCED SETUP
SAVE/RESTORE..
EXIT MENU
NORMAL
VIDEO I/O
VIDEO STANDARD
VIDEO LEVEL
COLOR BAR
PREVIOUS PAGE
PAL
|
|
|
|
80 110 150
OFF
- IMAGE ADJUST
GAMMA MODE: Adjusts the video signal to VIDEO I/O compensate for the
nonlinear response of the monitor display. Select AUTO to use 0.45 for NTSC
or 0.36 for PAL.
MANUAL GAMMA: Select MANUAL to
use a manual gamma correction set-
ting. 25 ~ 100 corresponds to gamma
value 0.25-1.
RESOLUTION: Standard/High optional
SHARPNESS: The higher the value is, the sharper the image is
SATURATION: The higher value is, the more saturate image is.
- CAMERA ID SETUP
ID DISPLAY: Select ON to display the
camera name.
CAMERA ID: The default is CAMERA.
Letter can be used:
abcdefghijklmnopqrstuvwxyz{|}~ !”#$%&’()*+,-./0123456789:;<=>?@ AB-
CDEFGHIJKLMNOPQRSTUVWXYZ[\]^_’
ID POSITION: UP-LEFT/ UP-CENTER/ UP-RIGHT/ DWN-LEFT/ DWN-RIGHT.
- IRIS
LENS SELECT: Supports both the DC-drive and Video-drive auto iris lenses.
Make sure that the Auto Iris setting in the OSD menu matches the actual
lens you are using. F<1.2 famous DC driver lens is recommended.
DC GAIN: Adjust the response sen-
sitivity of the auto-iris lens with light
level changes. The higher, the auto
iris will respond slowly to fast light
changes. If set too low, the auto iris
may conflict with the electronic shut
-
ter. Either will cause image brightness
to oscillate from light to dark to light.
The default is 50.
IMAGE ADJUST
GAMMA MODE
RESOLUTION
SHARPNESS
SATURATION
PREVIOUS PAGE
AUTO
HIGH
|
|
|
|
-8 0 8
|
|
|
|
-8 0 8
MANUAL GAMMA
GAMMA
PREVIOUS PAGE
|
|
|
|
25 45 100
CAMERA ID SETUP
ID DISPLAY
CAMERA ID
ID POSITION
PREVIOUS PAGE
ON
CAMERA
UP-LEFT
DC
DC GAIN
AI THRESH
PREVIOUS PAGE
|
|
|
|
0 50 255
|
|
|
|
-42 -18 60
VIDEO
AI THRESH
PREVIOUS PAGE
|
|
|
|
-42 -18 60
MANUAL
AI THRESH
PREVIOUS PAGE
|
|
|
|
-42 -42 60
LINELOCK
V PHASE
PREVIOUS PAGE
|
|
|
|
0 519 624
EXPOSURE
WHITE BALANCE
AE PREFs
AGC
WD RANGE
SHUTTER LIMIT
PREVIOUS PAGE.
ATW
HIGHTLIGHTS
MEDIUM
AUTO..
X2
PUSH AWB CONFIRM
All User properties will be written to ROM
CANCEL.
Save AWB & All Changs
*** WARNING***
WHITE BALANCE LIMITS
LOWLIMIT
HIGHLIMIT
PREVIOUS PAGE
|
|
|
|
2K 2000 5.5K
|
|
|
|
5.5K 10000 11K
2 YEARS WARRANTY
(See conditions of sales abstract)
