LUX 380464, Руководство пользователя

Страница: 34 / 144

GB
34
– Unscrew flange nut (7).
– Place the abrading disc onto the spindle. Comply
with the required installation position of the abrad-
ing disc.
– Place the flange nut onto the spindle. Note the
installation position of the flange nut:
1. Flange pointing away from abrading disc: for thin
discs such as cutting discs.
2. Flange pointing towards abrading disc: for thicker
discs such as abrading discs.
– Tighten the flange nut using the face pin wrench
provided while pressing the spindle locking but-
ton.
Commissioning
Adjusting the protective bonnet
►
P. 3, item 1
The protective hood must be adjusted so that it pre-
vents sparks and particles from being thrown in the
direction of the user.
– Loosen clamping lever (5).
– Adjusting the protective hood
– Tighten the clamping lever (5) again.
Operation
DANGER! Risk of injury! Let the appli-
ance idle for a few seconds before use.
When vibrations start to occur, replace the
abrading disc immediately.
WARNING! Risk of injury! The appliance
must be used only with the additional hand
grip fitted and the protective hood correctly
adjusted.
Check before switching on!
Check the safe condition of the appliance:
– Check it for visual defects.
– Check that all parts of the machine have been
securely fitted.
Switching on/off
WARNING! Risk of injury! After switching
off, the appliance continues to run on for a
few seconds. Wait until the abrading disc
has come to a stop before laying the appli-
ance down.
Note: In case of a loss of power, an under-
voltage relay is triggered. This prevents the
product from restarting by itself as soon as
the power is restored.
To switch on again the product must be
turned off at the main switch and then turned
back on.
►
P. 3, item 3
– Switching on: Press the On-Off switch (1), at the
same time, slide fowards and allow it to engage in
position
[1] .
– Switching off: Press the On-Off switch (1) briefly
and allow it to glide back to position [0] .
Tips on use
DANGER! Risk of injury!
Never use cut-
ting discs for abrading.
CAUTION! Risk of injury! The abrading
disc and work piece become very hot during
use. Let the abrading disc and work piece
cool down completely before touching them.
WARNING! Risk of injury! Always grind
with the specified surfaces:
• Cutting discs: Peripheral surface;
• Grinding disc, grinding wheel: Side sur-
face.
CAUTION! Risk of injury! The abrading
disc and work piece become very hot during
use. Let the abrading disc and work piece
cool down completely before touching them.
• Always clamp the work piece firmly.
•
Never tilt the appliance when cutting materials.
• Never apply excess pressure to the appliance.
Cleaning
Overview of cleaning
Regularly, depending on conditions of use
What? How?
Remove all dust from the
ventilation slits of the mo-
tor. Use a vacuum cleaner or
a brush.
Clean the machine. Wipe the unit with a
slightly damp cloth
Storage, transportation
WARNING! Risk of injury! Store the unit in
such a way that it cannot be started by unau-
thorised persons.
NOTICE! Risk of damage to the device!
Do not stored unprotected in a damp envi-
ronment.
Storage
– Clean unit before storing.
– Store the tool in a dry and well ventilated place.
Storage of grinding tools
Note: Unfavourable ambient conditions dur-
ing storage can accelerate the ageing pro-
cess of grinding tools.
– Always store abrasive bodies lying down on a
level surface.
– Only store abrasive bodies in dry and evenly tem-
pered, frost-free rooms.
– Protect abrasive bodies from direct sunlight dur-
ing storage.
Transportation
– When dispatching, try to use the original packag-
ing, if possible.