43
The machine can be operated with different trimming
heads according to the purpose for which it is being
used:
•
Impact knife:
exclusively
for trimming open
areas with strong growth such as: Weeds, high
grass, undergrowth, bushes, weed growth,
scrub, etc.
•
Filament head:
exclusively for trimming grass. It
can be used along walls, fences, lawn edges,
trees, posts, etc.
Connect both shaft tubes
– Pull out and hold locking bolt (20).
– Push the lower shaft pipe (6) into the upper shaft
pipe (5).
– Release locking bolt (20) again.
– Slightly turn the shaft pipes against one another
until the locking bolt (20) audibly engages.
– Tighten the clamping screw (21).
Fitting the operating bar
– Screw the operating bar (4) tight using the
screws (22) as illustrated.
Fitting the shoulder strap
– Hook the shoulder strap into the lug (2) on the
shaft tube.
Fitting the protective hood
– Use screws (23) to screw the protective hood (7)
to the trimming head (8)
Fitting the knife
– Remove and store the knife transport guard (e.g.
when storing the machine).
– Insert a suitable object (Allen key etc.) as shown
and hold it in the hole (25).
– Unscrew the hexagon nut (26) by rotating clock-
wise.
Caution: Left hand thread!
– Remove the pressure plate (27).
– Remove the blade flange (28).
– Attach the blade (29).
– Attach the blade flange (28).
– Attach the pressure plate (27).
– Tighten the hexagon nut (26) in counter-clock-
wise sense.
Caution: Left hand thread!
Fitting the filament spool
– Remove the transportation protection mecha-
nism from the cutting blade (24).
– Insert a suitable object (Allen key etc.) as shown
and hold it in the hole (25).
– Unscrew the hexagon nut (26) by rotating clock-
wise.
Caution: Left hand thread!
– Remove the pressure plate (27).
– Remove the blade flange (28).
– Place the filament spool (30) on the drive shaft,
and turn it hand tight in an anticlockwise direc-
tion.
Caution: Left hand thread!)
Operation
Filling with fuel
– Lay down the machine safely with the tank cap
facing up.
– Before opening the tank, clean the tank cap and
the filler nozzle if necessary.
– Slowly turn the tank cap (17) open and remove it.
– Slowly fill in the fuel mix. Avoid spilling!
– Check the seal inside the tank cap for damage
and replace it if necessary. Replace a damaged
seal immediately!
– Tighten the tank cap and seal by hand.
– In case you spilled some fuel: make sure to wipe
off the fuel.
Check the safe condition of the machine:
– Check the machine for leaks.
Check before use!
Check the safety devices and the safe condition of
the machine (especially tightening knob, protective
hood and trimming head):
– Check the machine for visual damage: broken
parts, cracks, etc.
DANGER! Risk of injury during installa-
tion!
No parts may be installed or removed
unless the motor has been turned off and
cooled down.
DANGER! Risk of injury during installa-
tion!
The knife is sharp. Wear cut-resistant
work gloves when installing the knife.
DANGER! Danger of injury!
There is a
sharp knife for trimming the filament on the
underside of the filament hood. Remove the
transport packaging only after installation.
DANGER! Danger of injury!
Fuel is explo-
sive!
– Turn off and cool the motor down
before filling the tank with fuel.
– You must observe all safety instruc-
tions relating to handling fuel.
Note:
DANGER! Attention, danger of injury!
Do
not operate the machine unless you did not
find any faults. If a part has become defec-
tive, make sure to replace it before you use
the machine again.
GB
Motorsense_302135_115326.book Seite 43 Mittwoch, 11. Januar 2017 10:23 10
