GB
25
Use the switch for drilling/hammer drilling (2) to select
the operating mode as follows:
•
Position
[
]
for hammer drilling in cement or
stone.
•
Position
[
]
for drilling without the hammer
function into wood, metal, ceramics and plastics
and for the screwdriver function.
Changing the rotation direction
NOTICE! Risk of damage to the unit!
Only use the rotation direction switch when
the device is at a standstill.
– To drill and screw screws into place, press the
rotation direction switch (6) to the left (rotation in
clockwise direction).
– To remove screws, press the rotation direction
switch to the right (rotation in an anti-clockwise
direction).
Electronic control of rotational speed
NOTICE! Risk of machine damage!
The
motor can overheat when running at low
speeds under continuous heavy load. Cool
off the motor by running at high speed with-
out a load.
The appliance is equipped with an electronic rota-
tional speed control.
The rotational speed is infinitely adjustable (Rota-
tional speed range:
).
– Turning the speed regulator (5) clockwise
increases the rotational speed.
– Turning the speed regulator anticlockwise
decreases the rotational speed.
Check before switching on!
Check to make sure the device is in safe operating
condition:
– Check to make sure there are no visible defects.
– Check to make sure all device components are
correctly mounted.
Switching on and off
– To start the tool turning, press the On/Off but-
ton (4).
– To operate permanently, press the locking but-
ton (3) whilst holding the On/Off switch down.
– To release the lock, press the On/Off switch again
and release.
– To switch the unit off, release the on/off switch (4).
Note:
The revolution speed of the device
can be varied by applying different pres-
sures to the on/off switch.
Drilling
DANGER! Risk of injury!
Never hold the
work piece that you are working with in your
hand, on your lap, or against other body
parts.
NOTICE! Risk of damage to the unit!
Never use the drill for chasing or to expand
drilled holes.
Always use a drill appropriate to the mate-
rial.
– Hold the device straight and drill with even pres-
sure.
Cleaning
Cleaning overview
Regularly and according to the operating condi-
tions
What?
How?
Clean the ventilation slots
of the motor to remove
dust.
Use a vacuum, cleaning
brush or paint brush.
Clean the device.
Wipe the unit with a damp
cloth.
Troubleshooting
What to do when something doesn’t work…
DANGER! Exercise caution – risk of
injury!
Unprofessional repairs may mean
that your unit will no longer operate safely.
This endangers you and your environment.
Malfunctions are often caused by minor faults. You
can easily remedy most of these yourself. Please
consult the following table before contacting the ven-
dor. You will save yourself a lot of trouble and possibly
money too.
Error/Fault
Cause
Remedy
Chuck is not turning.
No power supply?
Check the cable, plug, socket and the
fuse.
Is the device defective?
Contact your local vendor.
Wrong direction of rotation select-
ed?
Switch the rotation direction switch over.
Chuck is turning, but tool is not
drilling.
No hammer drilling functionality. Switch for drilling/hammer drilling
is not selected correctly?
Set the switch to the
[
]
position.
If you can’t fix the fault yourself, contact your nearest
vendor. Please be aware that any improper repairs
will also invalidate the warranty and additional costs
may be incurred.
Disposal
Disposal of the appliance
A crossed-out wheelie bin icon means: Bat-
teries and rechargeable batteries, electrical
or electronic devices must not be disposed of
Содержание 380453
Страница 3: ...1 1 2 7 8 3 4 5 6 2 1 3 ...
Страница 102: ...102 ...
Страница 103: ...103 ...
Страница 104: ...Art Nr 380453 V 080621 Emil Lux GmbH Co KG Emil Lux Straße 1 42929 Wermelskirchen GERMANY ...
