Bracket to bracket
(System Width)
Fabric Width
Lutron
®
roller 20
fascia mount
chassis
Installation Guide (please read before installing)
English
Box Contents:
Orient the buttons and wiring
4
Mount top/back cover
1
Pre-drill top/back to allow clearance for the entry of wires without
interfering with the bracket. Follow figure below for suggested hole
locations.
Notes:
•
Hole should be large enough to allow adjustment during install
without pinching the wire.
•
Cable should exit from EDU (Electronic Drive Unit) side of the system.
1.1
For the following bracket and button orientations, route the wires
through the wire slots.
Notes:
•
The buttons should be accessible when the shade is installed.
•
Make sure the wires are not pinched or damaged.
•
The wires must be routed through the top or bottom slots
4.1
Verify mounting surface is level/plumb before attaching top/back cover.
Note:
Top/back cover may rub fabric if installed with an improper tilt
or may cause flap to fall.
1.2
The roller 20 Fascia Mount Chassis Installation Guide
is a complement to the enclosed Basic Wiring and Setup Guide.
The Chassis Installation Guide describes the mechanical
installation. The Basic Wiring and Setup Guide describes the
wiring and setup for basic function of the roller shade.
Tools required:
• Tape Measure
• Level
• 1/4 in Hex-Head Driver
• Power Drill
• #2 Phillips Screwdriver
(1) Lutron roller 20 Shade
(1) Fascia with (2) Endcaps (rounded or square according to option chosen)
OR
(1) 4 in (102 mm) Cable Tie
(2) Bracket Leveling Spacers
(5) Mounting Screws
(#8x1-3/4 in Hex Head Screws)
(1) Cable Tie Anchor
(2) Fascia/Shade Brackets
with Retaining Screws
(1) Top/Back Cover
Position the mounting brackets
2
Mark the location of the mounting brackets so they are centered
over the window.
Notes:
•
Bracket to bracket distance = fabric width + 1.5 in (38 mm) =
system width.
•
For a ceiling and jamb mount, allow clearance to prevent fabric from
rubbing against trim, window, top treatment, etc.
•
Wall mount may require blocks to clear trim.
2.1
Install fascia brackets
3
Hook the top of the fascia bracket behind the top triangular tab of the
top/back cover. Then rotate the bracket until it snaps onto the bottom
tab of the top/back cover.
Note:
Put a screw in the center of each slot.
3.1
Mount the top/back cover using the appropriate fasteners. The ceiling side
of the top/back cover is the side with the larger of the two snapping tabs.
Notes:
•
The clearance hole for the wires and the screws must be at least 1.5 in
(38 mm) from system end to avoid the mounting brackets.
•
Be sure to pull cable through hole in pocket while mounting.
•
The top/back cover should be mounted to support at least 300 lbs (136 kg).
The fasteners provided may not be appropriate for use in all applications.
1.3
Mount the brackets.
Notes:
•
Put screws in both slots of either a wall mount or ceiling mount.
•
The brackets should be mounted to support at least 300 lbs (136 kg).
•
The fasteners provided may not be appropriate for use in all applications.
3.2
Mount the shade
5
Install the idler side of the shade onto its bracket.
5.1
Depress the spring-loaded idler (shown in 5.1) and install the Drive
side of the shade onto its bracket.
5.2
CAUTION:
Notes:
•
Lutron systems are intended for use with only Lutron hardware, controls,
and power supplies.
•
Codes:
Install in accordance with all local and national electrical codes.
•
Environment:
Ambient operating temperature: 32 °F - 104 °F
(0 °C - 40 °C), 0 - 90% humidity, non-condensing. Indoor use only.
•
Maintain sufficient clearance between the moving shade and any object.
Risk of falling objects. Securely install the roller shade
system per the mounting instructions. Failure to do so could
result in minor or moderate injury.
1.5 in
(38 mm)
1.5 in
(38 mm)
!
Buttons facing out
Wire slots
Buttons facing down
Wire slots
