Installation for lights with one wall switch (single-pole)
Installing your dimmer
OFF
ON
x3
Some lights have one wall switch, while others
have two or more wall switches (such as stair lights,
which have a switch at both the top and bottom
of the stairs). We’ve included instructions for lights
with one wall switch (called a single-pole). If your
light has more than one switch (called a 3-way),
please visit
www.casetawireless.com/3way
for complete installation instructions and how-to
videos.
WARNING: SHOCK HAZARD.
May result in serious injury or death. Turn off
power at circuit breaker or fuse before installing.
1
Turn power off at circuit breaker!
2
Press and hold “off” button on remote
4
Connect the dimmer
5
Mount the dimmer
6
Attach the wallplate
7
Turn power on at circuit breaker
2
Remove existing switch from wall
Remove the wallplate from switch.
3
Remove side sections (if necessary)
Remove the switch and pull it away from the wall.
* If your switch has more than 3 wires attached, see
“Installing Caséta
T
Wireless in a 3-way switch application”
video at
www.casetawireless.com/3way
Bend back
and forth.
3
5
1
4
6
Ground
Ground
1
2
3
Ground
7
2
Disconnect all three wires* from the switch.
1
Connect the bare copper (or green) “ground” wire
from the wallbox to the green wire on the dimmer
using a wire connector.
2
Connect either of the remaining wires from the
wallbox to either of the remaining wires on the
dimmer using a second wire connector.
3
Connect the remaining wire from the wall to
the remaining wire on the dimmer using a third
wire connector.
Do not
remove outside side sections
on dimmers at the end of gang.
Each dimmer
has inside side
sections removed.
Dimmer at middle has all
side sections removed.
Attach the adapter to the dimmer using the
screws provided and snap on the wallplate.
‘snap’
(If you installed the dimmer next to other dimmers
or switches, you’ll need to install a wallplate with the
correct size/number of openings to accommodate all
the devices.)
Use the screws provided.
Go to
www.casetawireless.com/support
for
additional troubleshooting suggestions.
For advanced features, tips on how to use Caséta
T
Wireless dimmers with CFLs and LEDs, the complete
Caséta
T
Wireless product line, and more, please visit
www.casetawireless.com/features
Changing the favorite light level
on the Pico
R
remote control
(optional)
You can use the round
“favorite” button on the Pico
R
remote control to recall a
favorite light level. We’ve set
it to 50%, but you can change
it to any level you like.
Favorite
CAUTION
Use only with permanently installed fixtures with
dimmable LED, dimmable CFL, halogen, or
incandescent lamps. To avoid overheating and
possible damage to other equipment, do not use
to control receptacles, motor-driven appliances,
or transformer-supplied appliances.
Codes
Install in accordance with all national and local
electrical codes.
Grounding
When no “grounding means” exist in wallbox, the
National Electrical Code (NEC
®
) allows a control to
be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic
attachment screws or 2) the circuit is protected by a
ground fault circuit interrupter (GFCI). When installing
a control according to these methods, cap or remove
green wire before screwing control into wallbox.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Lutron, , Claro, and Pico are registered trademarks and FASS, Caséta,
and Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is
a registered trademark of the National Fire Protection Association,
Quincy, Massachusetts. Google and the Google logo are registered
trademarks of Google Inc., used with permission.
© 2014 Lutron Electronics Co., Inc.
P/N 0301716 REV B
3
3
4
4
2
2
1
2
2
2
1
2
2
2
Hold for 6 seconds until LEDs
blink twice. New favorite
level is now saved.
3
Set desired light level on dimmer
4
Press and hold “favorite” button on remote
x2
Important note:
Symptoms
Probable cause and action
Light does
not turn on or
in-wall dimmer
LEDs do not
light up.
• Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
• FASS
T
switch on the dimmer
is in the Off position.
Light does
not respond
to Pico
R
remote
control.
• The dimmer failed to pair
with Pico
R
remote control;
see Pairing the dimmer and
Pico
R
remote control
.
• The dimmer is already at the
light level the Pico
R
remote
control is sending.
• The Pico
R
remote control
is outside the 30 ft (9 m)
operating range.
• The Pico
R
remote control
battery is low.
• The Pico
R
remote control
battery is installed incorrectly.
• Bulbs turn off
while being
dimmed.
• Bulbs turn on at
high light level
but do not turn
on at a low
light level.
• Bulbs flicker
or flash when
dimmed to a low
light level.
Verify bulbs are marked
dimmable and visit
www.casetawireless.com/
lowend
for information on adjusting
the dimmer for best
bulb performance.
Troubleshooting
Hold for 6 seconds
until lights flash 3 times.
5
5
Repeat steps to pair other
Pico
R
remote controls.
Device Ratings
In-wall dimmer
PD-6WCL
120 V
~
50/60 Hz
Pico
R
remote control
PJ2-3BRL
3 V
-
10 mA
(1) CR2032 battery
(included)
quick-start guide
Pico
R
remote control & in-wall dimmer
Welcome
—and thank you for purchasing a Caséta
T
Wireless dimming kit. In order to control your lights from
an app or remote,
you’ll need to replace an existing
switch with a Caséta
T
Wireless in-wall dimmer.
Before you install the dimmer, please watch the
installation video at
www.casetawireless.com/support
We hope you enjoy the convenience of Caséta
T
Wireless!
Contents supplied
Double your warranty
In-wall dimmer
(PD-6WCL)
Claro
R
wallplate
(CW-1)
Tools you’ll need
Flat-head screwdriver
Pico
R
remote control
(PJ2-3BRL)
Wire connectors (3)
Phillips-head screwdriver
Pliers
Screws (2)
Love Caséta
T
Wireless dimmers? Have ideas
for making them better? Tell us what you think
and we’ll extend your warranty by 1 year.
www.casetawireless.com/register
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
P/N 0301716 REV B
Wireless
Hold for 6 seconds
until LEDs start
blinking.
1
Press and hold “off” button on dimmer
Pairing the dimmer and
Pico
R
remote control
The Lutron
R
app will walk you through
setting up your devices.
www.casetawireless.com/LutronApp
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
Important notes:
1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
Replacing light
bulbs using
FASS
T
Pull the FASS
T
switch out on the
in-wall dimmer to
remove power at
the light socket.
On
Off
Darker
Brighter (with raised icon)
FASS
™
Front Accessible
Service Switch
Pico
®
remote control
On
Off
Darker
Favorite
Brighter
With a smartphone or tablet
(Bridge required, sold separately)
Lutron
The Caséta
T
Wireless dimmer can be controlled from a smartphone when used
with the Lutron
R
Smart Bridge
T
.
If you are using the dimmer and remote control with the Lutron
R
Smart Bridge
T
follow the instructions below.
Using your Cas
é
ta
T
Wireless kit
Without a smartphone or tablet
(Bridge not required)
Search for “Lutron Caseta”
Lutron
Lutron
R
Smart Bridge
T
Note:
If you are using the dimmer and remote control with another
manufacturer’s bridge, please refer to that manufacturer’s instructions
for set-up.
Lutron
Lutron
R
app
3
Add
devices
• Pico
R
remotes
• Dimmers
• Shades
Control
three ways
Schedule
your lights
Connect
while away
Apple is a trademark of Apple Inc., registered in the U.S. and other countries. AppStore is a service mark of Apple Inc.
3
Use the Lutron
®
app to complete
ALL
remaining steps
2
Launch the Lutron
®
app
1
Download the Lutron
®
app
Using your controls
Important note:
Removing side sections reduces the dimmer’s
maximum wattage rating. See the chart below
for maximum wattage information.
Maximum* wattage derating chart
(120 V
~
50/60 Hz)
Side sections
removed
None
1 side
2 sides
LED & CFL
150 W
150 W
150 W
or*
Incandescent &
Halogen
600 W
500 W
400 W
* For maximum wattage information when
mixing light bulb types see
www.casetawireless.com/ganging
Works with energy efficient
dimmable light bulbs:
NOTE:
You can mix and match dimmable LED and
CFLs, as well as halogen and incandescent light
bulbs, with Caséta
T
Wireless dimmers.
Dimmable LED and CFL light bulbs vary in their
dimming performance. If you’re using these
bulbs and they flicker or turn off, please visit
www.casetawireless.com/lowend
for information
on adjusting the dimmer for best bulb performance.
For a complete list of compatible dimmable LEDs
and CFLs, please visit
www.casetawireless.com/bulblist
Compatible light bulbs include:
Cree
R
BA19-08027OMF-12DE26-1U100
CR6-575L
Ecosmart
R
ECS BR30 W27 FL 120
ECS 20 WW FL 50WE 120
Feit
R
A19/OM/LED
Philips
R
9290002295
Sylvania
R
LED12A19/DIM/O/827
LED21PAR38/DIM/P/930/FL30
CFL
—up to 150 W
LED
—up to 150 W
Halogen
—up to 600 W
Incandescent
—up to 600 W
