GENERAL INFORMATION
This instruction manual contains important notifications regarding
the safe use of the CONNECT-RX100.
Please take the time to read this manual carefully and thoroughly
before installing and operating the system.
We recommend you keep a copy for future use and you transfer it
to the buyer if you resell the system.
EXALUX reserves the right to modify and upgrade its range of
products, with no obligation to integrate these changes into
products already sold. Therefore, all the information found in this
manual is subject to change without notice.
SAFETY INSTRUCTIONS
Proper use:
This unit is designed to control lighting sources using DMX
commands. Use the device only in its intended use as described in
this manual. Any other use, as well as use in other conditions, will be
considered non-compliant and can cause injury and damage. No
liability will be assumed for damages resulting from improper use.
The device should only be used by people in full possession of
their physical, sensory and mental abilities who must have the
knowledge and experience required. All the other persons are only
allowed to use the device under the supervision or direction of a
person responsible for their safety.
Safety:
Risk of electric shock
This system requires high voltage, which can result in an electrical
shock. Never remove covers. The parts inside the device are
maintenance free.
Dangers for children
Ensure a proper disposal of plastic envelopes and packaging.
They should not be near babies nor young children: suffocation
danger. Make sure that children do not remove small parts of the
unit (e.g. knobs, screws or similar). Children could swallow the
pieces and choke. Never leave unattended children use electrical
devices.
Electric shock caused by a short circuit
Do not modify the power cord nor the plug. In case of non-
compliance, there is a risk of electric shock and fire hazard and
death. If in doubt, contact a certified technician.
Risk of fire
Never cover the device nor its ventilation slots. Do not install the
device close to a source of heat. Keep the device away from flames.
Terms of use
The device is designed for indoor use. To prevent damage, do
not expose the product to liquid or moisture. Avoid direct sunlight,
clogging and strong vibrations.
Power supply
Check the operation of the power supply before connecting to
the system.
Before connecting the appliance, check if the voltage indicated
on the device matches the voltage on the local supply network
and if the socket is fitted with a differential circuit breaker. In case
of non-compliance, the device could be damaged and the user
might be injured.
When a storm is announced or the unit must not be used for an
long time, unplug it to reduce the risk of electric shock or fire.
CARE
– Unplug the unit when cleaning it and during all maintenance
operations.
– Do not use cleaning product: use a dry cloth and rub gently.
– Store the device in a clean, dry place, away from direct
exposure from sunlight and dust.
EXALUX est une marque déposée
de la société française LEDIXIS
EXALUX is a registered trademark of
the French Tech company LEDIXIS
1 rue de la Noë - Bat. IM3
CS 12111 | 44322 Nantes cedex 3 | FRANCE
+33 (0)9.72.45.70.43
www.exalux.eu
Information :
Support technique / Technical support :
Dernière mise à jour / Last updated on 01/2017
(1)
powerCON Connector
Power supply
100-240VAC
(2)
XLR4 Connector
Battery input 5-24VDC
(3)
XLR5 Connector
DMX output
(4)
Connect button
(5)
LED indicators
OVERVIEW
OPERATING PRINCIPLE
The CONNECT-RX100 is a wireless DMX receiver, that uses
LumenRadio CRMX technology (2.4GHz). This system allows the
users to control DMX enabled fixtures wirelessly, several hundred
meters away.
CONNECT-RX100 can receive an entire DMX universe (512
channels) without any latency.
A complete system is composed of a CONNECT-TX100 transmitter,
linked with one or several CONNECT-RX100 receivers, and can be
controlled from a standard DMX controller.
Several CONNECT-TX100 + CONNECT-RX100 can be used
simultaneously, in order to transmit several DMX universes.
POWER SUPPLY
The CONNECT-RX100 offers two power supply inputs:
(1)
and
(2)
.
The first power supply input using powerCON connector
(1)
is an
AC power supply (100-240 VAC 50/60Hz).
The second one, using a XLR4 connector
(2)
, is dedicated to
batteries with DC current between 5 and 24 Volts. Only pins 1 and
4 are connected. Pin 1 is used for GND and pin 4 is used for +VCC
(cf. opposite diagram). To provide supply to the CONNECT-RX100,
DMX OUTPUT
The DMX signal received form the radio-transmitter is outputed on
the XLR5
(3)
, with the standard pinout :
Pin1: GND | Pin2: DMX- | Pin3: DMX+
Connect all the DMX fixtures to control on this DMX output.
The indicator
DMX512 (5)
turns on when a DMX signal is received
and outputed on the XLR5.
LINKING WITH TRANSMITTER
By default, CONNECT-RX100 do no listen to the data sent by the
transmitter CONNECT-TX100: it is necessary to link the receivers to
the transmitter.
In order to link a CONNECT-RX100 to a CONNECT-TX100, follow this
procedure:
- Make sure both devices are powered.
- Start the linking procedure by pressing the dedicated button
on the CONNECT-TX100.
- During the linking period (10s), any unlinked CONNECT-RX100
in range will automatically link to the CONNECT-TX100.
If a CONNECT-RX100 is linked to a transmitter, the
Paired (5)
indicators turns on (even if the transmitter is off).
If a CONNECT-RX100 is linked to an active transmitter, both
Paired
and
RF Link (5)
indicators turn on.
If a linking problem occurs, the
RF Link (5)
indicator blinks. It is
necessary to restart the procedure.
Several receivers CONNECT-RX100 can be linked during a single
procedure.
During the linking procedure, the DMX signal is not transmitted.
UNLINKING RECEIVERS
At any moment, it is possible to reset the configuration of the
CONNECT-RX100, by unlinking the transmitter.
To do so, press the button
(4)
during 3 seconds, until the
Paired
(5)
indicator turns off.
The CONNECT-RX100 can then be linked to any transmitter.
RADIO
A four-level gauge
(5)
provides a feedback on the radio signal
strength.
In order to optimize the radio communication, it is recommanded
to install the transmitters and receivers in open spaces, without
large metalic objects.
It is also recommanded to place the antennas as described in the
following image.
LUMENRADIO COMPATIBILITY
EXALUX recommands the use of the transmitters CONNECT-
TX100. Nevertheless, the CONNECT-RX100 can be used with any
transmitter compatible with CRMX Technology from LumenRadio.
For more information, refer to www.lumenradio.com.
one of these two connectors has to be
connected to an adapted power supply.
If both power supplies are connected at
the same time, only AC power supply
connected to powerCON connector
(1)
will be used.
The
Power (5)
inidicator turns on when
the device is powered.