Lufft 8511.EAK Скачать руководство пользователя страница 9

Страница: 9 / 158

3.3 GPRS Modem Connection for Wireless TCP/IP Connections,

and Analog Modem for PPP-Dial In Connections.

The supported modem for GPRS Connections is: Wavecom Fastrack GPRS Modem.

Serial port settings are 115200 baud, 8 data bits, no parity, 1 stop bit, RTS/CTS

hardware handshake enabled.

Alternative modems can be tested on request.

LCom

Connection

GPRS Modem

RXD1 (CON220-1/Pin 7)

RS232

RXD (Pin 6)

TXD1 (CON220-1/Pin 8)

RS232

TXD (Pin 2)

RTS1 (CON220-1/Pin 9)

RS232

RTS (Pin 12)

CTS1 (CON220-1/Pin 10)

RS232

CTS (Pin 11)

GND (CON220-2/Pin 2)

RS232 (if required)

GND

GUB_2 (CON220-2/Pin 1)

Power supply

UB+ - 1V

GND (CON220-2/Pin 2)

Power supply

GND

LCom/GPRS modem wiring

For the PPP Dial In Connection, any Hayes compatible modem may be used. Serial

port settings are 57600 baud (configurable, see modem dialog below), 8 data bits, no

parity, 1 stop bit, RTS/CTS hardware handshake enabled.

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Похожие инструкции для 8511.EAK

Бренды по названию

Популярные бренды