Lufft 8511.EAK Скачать руководство пользователя страница 77

Страница: 77 / 158

Manual

LCom

Page 77 of 158

Note: the bigger the value for the reporting interval is, and the more Sensor

OIDs are configured for the data store, the longer it takes for the rpu to read

and calculate the aggregated data for each OID (which is calculated

depending on the statistics Type settings for the respective OID in the

historySensors table). Calculating the data might take up to several minutes!

The maximum number of entries in the resultsTable is 255

– so if more than

255 rows are to be expected, the status reported above will be

“dataPartialReady”.

f) Read the number of valid rows in the results table through reading the

dataStore.numRowsInResult.0

OID

Note: if the query was successful (no error occurred), but there are no values

available in the given interval, the number of rows in the result will be reported

as 0.

g) Read the resultsTable

–

dataStore.queryResultsTable.queryResultsEntry.rowMeasureT

ime.x

will provide the UTC timestamp of the measure values reported by the

corresponding

dataStore.queryResultsTable.queryResultsEntry.rowValues.x

OID.

h) Read

the “dataStore.resultEndTime.0” parameter. This reports the end of the

interval analyzed for the current result set. If the data provided does not cover

all the time period needed (the

dataStore.queryCommandAndStatus.0

value will be dataPartialReady (4) if more data is available in the

data store), re-calculate a new startTime timestamp and repeat

from step c) !

i) After all values have been retrieved, clear the result set (and query

parameters) by writing a value of 7 (done) to the

dataStore.queryCommandAndStatus.0

OID.

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды