Lufft 8511.EAK Скачать руководство пользователя страница 5

Страница: 5 / 158

Please Read Before Use

Before using the equipment, please read the operating manual carefully and follow

the instructions in every detail.

1.1 Symbols Used

Important information about potential hazards to the user

Important information about correct equipment operation

1.2 Safety Instructions

•

Installation and commissioning must only be carried out by suitably qualified

specialist personnel.

•

Never take measurements on or touch live electrical parts.

•

Pay attention to the technical data and storage and operating instructions.

1.3 Designated Use

•

The equipment must only be operated within the range of the specified technical

data.

•

The equipment must only be used under the conditions and for the purposes for

which it was designed.

•

The safety and operation of the equipment can no longer be guaranteed if it is

modified or adapted.

1.4 Guarantee

The guarantee period is 12 months from the date of delivery. The guarantee is

forfeited if the designated use is violated.

1.5 Incorrect Use

If the equipment is installed incorrectly

•

It may not function at all or its function may be limited



Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды