manualshive.com logo in svg

Lufft 8511.EAK, Руководство по эксплуатации

Поделиться
Скачать
Lufft 8511.EAK Скачать руководство пользователя страница 34

5.8.2  Configuration 

The 

“Ntcip” dialog on the LCom (or via the service program) is used to configure the 

NTCIP protocol parameters. The input fields of this dialog are only enabled if 

“Ntcip” 

is selected 

as the protocol in the “Uplink” dialog. 

 

 

 

Note: The number of entries in the related tables, i.e. the number of sensors of 

corresponding type that are available in the system, is set by configuring the 

respective tables (windSensorTable, essTemperatureSensorTable etc.). Also, sensor 

values can onl

y be assigned to previously configured table entries via “Sensor 

Assignment”. So before assigning the actual UMB sensors to the respective NTCIP 

OIDs, you need to set up the various “sensor tables” (to configure the number of wind 

sensors, temperature sensors, pavement sensors etc.). 

 

 

Note for TSS: TSS values are retrieved from a Wavetronix sensor via an UMB 

Wavecon device. Data storage must be activated for these sensor channels in order 

to transmit these sensor values via NTCIP-TSS. 

Содержание 8511.EAK































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды