Lufft 8511.EAK Скачать руководство пользователя страница 28

Страница: 28 / 158

5.7.3 TLSoIP Parameter

Parameters for TLSoIP according to the TLSoIP Specification (AsfinAG). At the

moment only the

“bidirectional connection” with a permanent connection to the server

is supported.

•

C_ConnectDuration: Not used (for “unidirectional connection” only)

•

C_ConnectDelay: Not used (for “unidirectional connection” only)

•

C_ReconnectDelay: Minimum time between two connection attempts

•

C_HelloDelay: Time between “Keep Alive” telegrams

•

C_HelloTimeout: Timeout for receiving

of “Keep Alive” telegrams

•

C_ReceiptCount: Number of data telegrams after which a receipt is sent or

expected

•

C_ReceiptDelay: Time after receiving a data telegram after which a receipt is

sent, even if C_ReceiptCount was not yet reached

•

C_ReceiptTimeout: Timeout for receiving a receipt

•

Use GPRS modem: If the TLSoIP connection is made via the GPRS modem,

the software always waits for the GPRS connection to become active before

establishing a connection to the server. This should be turned off if the

connection is made via LAN interface so that the TLSoIP connection does not

wait for the GPRS connection to be established.

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды