Lufft 8511.EAK Скачать руководство пользователя страница 25

Страница: 25 / 158

5.7 Uplink-Type and common TLS Parameter

The parameters for the Uplink protocol are configured via “Uplink”. At present “TLS”

(TC 57), “TLSoIP”, “NTCIP” and “Micks FTP” are supported.

If NTCIP is selected, all TLS parameters are disabled. The parameters for NTCIP are

set in the dedicated “NTCIP” dialog (see below).

•

Uplink type: TLS-INSELBUS, TLSoIP, TLS-LOKALBUS, Micks-FTP or NTCIP.

•

Trace level: Trace level for the transfer protocol (not yet fully implemented).

Common TLS parameters are:

•

FG3 M

ode: The transfer mode for the FG3 data: “Periodic” or “On Request”.

•

FG3 Period: The time period in between transmissions for the

“Periodic”

transmission mode.

•

FG6 M

ode: The transmission mode for the FG6 data: “Periodic”, “On Request”

or “On Change”.

•

FG6 Period: The time period in between transmissions

in “Periodic”

transmission mode.

•

OSI7 node number: The unique OSI7 node number for the SM/EAK.

•

OSI2 address: The unique OSI2 address of the device on this Inselbus.

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды