Lufft 8511.EAK Скачать руководство пользователя страница 114

Страница: 114 / 158

Manual

LCom

Page 114 of 158

If the model calculation is active, “virtual” output sensor channels for the simulated

saline concentration and freeze temperature are created automatically for every

configured instance.

5.13.7 Fresh Snow Height

Here the parameters for the fresh snow height model calculation are configured. The

model calculates 2 values that are represented by 2 (virtual) sensor channels: fresh

snow amount for measurement interval (i.e. every minute), and fresh snow amount

since daybreak.

•

Model active:

the model calculation is active/inactive

•

Min Snow Density:

minimum density of snow pack (kg/mm*m²)

•

Max Fresh Snow Density:

maximum density of fresh snow (kg/mm*m²)

•

Min Temp for Max Snow Density:

minimum temperature for maximum snow

density (°K)

•

Snow Factor Precipitation:

multiplication factor for precipitation

•

Precipitation Type:

precipitation type sensor

Содержание 8511.EAK































































































































































Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды

Lufft 8511.EAK, Руководство по эксплуатации

Результаты поиска

Содержание 8511.EAK

Отзывы:

Бренды по названию

Популярные бренды