Lucent 23N12 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 176

Lucent 23N12 Скачать руководство пользователя страница 99

255-700-714R11.0

4-9

PacketStar

®

PSAX 1-Port Channelized OC-3/STM-1 CES Module User Guide

, Issue 1

Release 11.0.0

Chapter 4 Configuring the STM-1 Mode Ports and Channels Using the Console

Obtaining General Module Data and Accessing Ports and Channels

The Alarm Status field on the Equipment Configuration window is described
in Table 4-3.

SW #

Default:

N/A

Range: N/A

Format: Predefined

Displays the version of PSAX system software with which
the modules’ firmware was released. The software version is
encoded in the module firmware. Because not all modules
require firmware upgrades with every new PSAX system
software release, the software version that is displayed in
this window may be lower than the CPU system software
that is currently running on the PSAX system. See the most
recent Release Note document for the latest software and
firmware lineup information.

PEC

Default:

N/A

Range: N/A

Format: Predefined

Displays the product element code (PEC) used to identify
and order this type of module. The PEC is encoded in the
module bootloader.

Serial #

Default:

N/A

Range: N/A

Format: Predefined

Displays the unique serial number of the individual module.
The product serial number is encoded in the module firm-
ware.

For PSAX System Rel. 6.5.0 and later: 12-digit number in
the format,

YYVVDDnnnnnn

, where

YY

= year of manufac-

ture

VV

= vendor ID code (manufacturer and location)

DD

=

date code of manufacture (either month or week depending
on vendor preference)

nnnnnn

= sequential number, which

in conjunction with

YY, VV

, and

DD

, creates a unique num-

ber for each hardware component in the PSAX product line.

For existing products with the 10-digit serial number used
in Rel. 6.5.0 or later, this number is displayed with two pre-
ceding zeros.

For PSAX Rel. 6.3.0 and earlier: 10-digit number. For prod-
ucts with 12-digit serial numbers used in Rel 6.3.0 or earlier
systems, the first two digits (

YY

) are not displayed.

Table 4-2. Equipment Configuration Window Field Descriptions (Continued)

Field Name

Field Value

Description

Table 4-3. Module Alarm Status Descriptions on the Equipment Configuration Window

Alarm Status

Module Type

Affected

Description

NoAlarm

I/O and Server Indicates that no alarms have been detected for the module

in this slot.

WrongCardType

I/O and Server Indicates that one type of module was configured in this

slot in the chassis, but a now different module occupies this
slot.

LineFailed

All

Indicates that the module in this slot is no longer receiving
or transmitting signals because the line failed.

«
...
97
98
99
100
101
...
»

Содержание 23N12

















































































































































































Отзывы:

Нет отзывов