manualshive.com logo in svg

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Поделиться
Скачать
Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 493

Issue 1.0

March 2001

12-21

365-575-389

Installation Manual

Troubleshooting

Troubleshooting Information

Introduction

The following sections are referred to by other procedures throughout this manual.

CMC Connection 
Requirements

This paragraph describes the minimum requirements for the physical connection 
between the CMC PC and the WaveStar OLS 40G.

Figure 12-1 on page 12-22 shows the minimum cabling needed. The RS-232 
control lead values are listed for the DCE (user panel) and DTE (backplane) 
connectors. The WaveStar OLS 40G terminal does not change these control lead 
values or do any active handshaking during communications sessions. The CMC 
program does actively handshake as follows: 

■

When a carriage return is entered from the product selection menu of the 
CMC program prior to the login screen, the PC DTR and RTS leads go 
high.

■

After the DTR and RTS leads are set to high the CMC program expects the 
CTS and DSR leads to go high.

If the CTS and DSR leads do not go high on the correct COM port then the CMC 
program will immediately issue a “Communication with the NE cannot be 
established” error message. If the error message is reported after several 
seconds then the handshaking is probably correct and the problem is with the 
data transmission being corrupted. If a local area network is used to connect the 
CMC PC to the WaveStar OLS 40G, XON/XOFF handshaking must be disabled at 
both ends of the network connection.

(Continued on next page)

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды