Lucent Technologies WaveStar OLS 40G Скачать руководство пользователя страница 376

Страница: 376 / 578

8-10

Issue 1.0

March 2001

365-575-389

Installation Manual

Network Element Startup and Provisioning

Connecting to the NE (Continued)

Procedures
(continued)

Figure 8-4.

Network Element Login Window

Step

Action

Reference

Enter User ID, Password and Privilege Level:

— Default User ID: LT01 (All caps with a zero.)

— Default Password: FT-2000 (All caps with zeros.)

— To Set the Privilege Level, use downward arrow.

Click on EXPERT.

Figure 8-3

CenterLink will connect to the Network Element and a
Login Successful confirmation will be received.
If no connection is established:

Verify that the RS-232 cable is connected
properly between the COM port and the NE.

Verify NEServer is running.

Return to the login command and try again.

This completes the Login to the Network Element.

Select appropriate
security levels

Default=LT01

Default=FT-2000

Click Enter to Proceed

Содержание WaveStar OLS 40G



































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание WaveStar OLS 40G

Отзывы:

Бренды по названию

Популярные бренды

Lucent Technologies WaveStar OLS 40G, Руководство по установке

Результаты поиска

Содержание WaveStar OLS 40G

Отзывы:

Бренды по названию

Популярные бренды