Lucent Technologies Voice Terminal 8405 Скачать руководство пользователя страница 31

Страница: 31 / 92

The 8400-Series Voice Terminals Instructions for Installation, Switch,
Administration, and Programming the Options

555-015-725

Issue 1

October 1996

Installing Your Voice Terminal

Page 3-13

Wiring Information

Wall Installation

Only the 8403, 8405, and 8410 voice terminals can be wall-mounted. The 8411
and 8434DX voice terminals CANNOT be wall-mounted.

Use the following directions for wall-mounting the 8403, 8405, and 8410 voice
terminals.

Wall-Mounting the 8403, 8405, and 8410 Voice
Terminals

NOTE:

For wall-mounting these voice terminals, you need a 1-foot D8W line cord
(not supplied with the voice terminal; Comcode: 103786760).

1. Make sure the 8-conductor wall mount plate is in place.

2. Press down on the handset retainer hook located under the handset and

slide it toward the top of the voice terminal. See Figure 3-6.

3. Rotate the hook and slide it back into its slot so the bottom part now sticks

out from the top. Snap the hook firmly into place. See Figure 3-6.

Figure 3-6.

Reversing the Handset Hook

a. Handset

retainer

b. Press to release

and then remove

handset retainer

d. Replace

handset
retainer

in place

c. Rotate

handset
retainer
180 degrees

Содержание Voice Terminal 8405





























































































Результаты поиска

Содержание Voice Terminal 8405

Отзывы:

Похожие инструкции для Voice Terminal 8405

Бренды по названию

Популярные бренды

Lucent Technologies Voice Terminal 8405, Инструкция по эксплуатации

Результаты поиска

Содержание Voice Terminal 8405

Отзывы:

Похожие инструкции для Voice Terminal 8405

Бренды по названию

Популярные бренды