background image

INTERFERENCE INFORMATION

FCC REGULATIONS PERTAINING TO THIS EQUIPMENT

NOTICE

Federal Communications Commission (FCC) rules require that you be notified of the following:

FCC (Part 15)
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions in the installation, administration and user manuals
may cause interference to radio and television communications.
This equipment has been tested and found to comply with the limits for a Class A computing
device, pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial environment.
Operation of this equipment in a residential area may cause interference with nearby radios or
television, in which case the owners (at their expense) will be required to take whatever measures
may be necessary to correct the interference.
FCC (Part 68)
This equipment is registered with the Federal Communications Commission (FCC) in accordance

with Part 68 of its Rules. The FCC requires that the manufacturer provides you with the
following information:
1. CONNECTION AND USE WITH THE NATIONWIDE TELEPHONE NETWORK
The FCC requires that you connect your telephone equipment to the nationwide telephone
network through a standard telephone network interface jack such as a USOC RJ11C.
Registered equipment may not be used with Coin Telephone Lines. Equipment may be used
with Party Lines in areas where state tariffs permit such connections and when equipment is
adaptable for such use.
2. INFORMATION FOR THE TELEPHONE COMPANY
Upon request of your local telephone company, you are required to provide them with the
following information:
A. The lines to which you will connect the telephone equipment.

B. The FCC registration number, AS593M-72132-KF-E, and ringer equivalence number (REN),
0.3A/0.5B. Both numbers are on the controller. The REN is useful to determine how many
devices you may connect to your telephone line and still have them ring when your telephone
line is called. In most, but not all areas, the sum of all REN’s per line should be 5 or less.
You may want to contact your local telephone company for specific information.
The local telephone company must also be notified upon final disconnection of the equipment
from the local telephone company lines.

3. REPAIR INSTRUCTIONS

If it is determined that your telephone equipment is malfunctioning, the FCC requires that it

not be used and that it be unplugged from the modular outlet until the problem has been

corrected. Repairs to this equipment can be made only by the manufacturer or its authorized
agents. For repair procedures, follow the instructions outlined under the AT&T Limited
End User Warranty.
4. RIGHTS OF THE TELEPHONE COMPANY
If telephone equipment is causing harm to the telephone network, the telephone company may
temporarily discontinue your telephone service. If possible, they will notify you before they
interrupt service. If advance notice is not practical, you will be notified as soon as possible.
You will be given the opportunity to correct the problem, and you will be informed of your right
to file a complaint with the FCC.
Your telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect the proper functioning of your equipment. If such changes are
planned, you will be notified.
5. THIS EQUIPMENT IS COMPATIBLE WITH INDUCTIVELY COUPLED HEARING AIDS.

Содержание Spirit 308





















Отзывы: