Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 332

Страница: 332 / 365

Maintenance

B-7

To use Table B-1, first locate the item you want. A triangle ( ) indicates where you can obtain it.

SOURCE (U.S.)

PARTNER-34D corded telephone

PARTNER-18D corded telephone

PARTNER-18 corded telephone

PARTNER-6 corded telephone

Backup/Restore PC Card

Contact Closure Adjunct

PARTNER-CA48 Intercom Autodialer

Button label package (specify telephone model)

Button label package (PARTNER-CA48 Intercom Autodialer)

Handset (AB1A)

Standard for PARTNER-model phones

Amplified handset (K6S)

Optional for hard-of-hearing users with PARTNER-model phones

Handset cord, 9 ft., coiled

Connects handset to telephone

Telephone mounting cord (D4BU)

Connects phone to wall jack, jack panel, or 206E
module ext. jack. Specify length: 2, 7, or 14 ft.

Modular telephone extension cord —8-connector

Extends the D4BU mounting cords
Specify length: 14, 25, 50, 75, or 100 ft.

System Telephones and Accessories:

Lucent

Direct

Catalog

Sales

(800) 451-2100

Lucent

Technologies

Sales

Office

(800) 247-7000

Lucent

Technologies

Authorized

Dealer

Lucent

Technologies

National Parts Sales

Center

(800) 222-7278

To locate the nearest Lucent Technologies Authorized Dealer, check your local telephone directory’s yellow pages.

Table B-1. —

Continued

Содержание PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Результаты поиска

Содержание PARTNER Advanced Communications System Release 1.0

Отзывы:

Похожие инструкции для PARTNER Advanced Communications System Release 1.0

Бренды по названию

Популярные бренды

Lucent Technologies PARTNER Advanced Communications System Release 1.0, Инструкция по программированию и эксплуатации

Результаты поиска

Содержание PARTNER Advanced Communications System Release 1.0

Отзывы:

Похожие инструкции для PARTNER Advanced Communications System Release 1.0

Бренды по названию

Популярные бренды