Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 319 | Manualshive

Страница: 319 / 365

background image

System Problems

Calls on Hold Are Disconnected

Possible Cause: Hold Disconnect Time setting is too short.

What to do: Change

Hold Disconnect Time (#203)

to a longer interval.

If calls on hold no longer disconnect, the problem is solved.

If calls on hold still get disconnected, or the Hold Disconnect Time was already set to
the longest interval, call the hotline.*

Call on Hold Hangs Up,
but Line Does Not Disconnect

Possible Cause 1: Hold Disconnect Time setting is too long.

What to do: Change

Hold Disconnect Time (#203)

to a shorter interval.

If abandoned calls on hold are disconnected, the problem is solved.

If abandoned calls on hold still do not disconnect, or if the Hold Disconnect Time
was already set to the shortest interval, go to Possible Cause 2.

Possible Cause 2: Local phone company does not send hold release signal.

What to do: Call your local phone company and find out whether they send a hold release
signal. If the local phone company does not send a hold release signal, or if they do but
the problem still occurs, call the hotline.*

All Calls Disconnected

Possible Cause 1: You just ran the

Restore Programming (#125)

procedure.

What to do: This is normal behavior after running

Restore Programming (#125)

; the

system resets itself. In the future, warn users before beginning the restore, or perform the
restore during nonbusiness hours. If you did not run

Restore Programming (#125)

, go to

Possible Cause 2.

Possible Cause 2: Power was interrupted to the control unit.

What to do: Make sure the control unit’s power cord is plugged securely into the wall
outlet. Also make sure the on/off switch is in the “ON” position (“O”) if you have a 5-Slot
carrier.

If the green LEDs on the modules are lit and the trouble is gone, the problem is
corrected.

If the green LEDs on the modules are lit but the trouble remains, call the hotline.*

If the green LEDs on the modules are out, go to Possible Cause 2 in “All Phones
Dead: No Dial Tone or Lights.”

If any green LEDs on the modules are flashing, call the hotline.*

*

In the continental U.S., help is available at 1 800 628-2888. Outside the continental U.S., call your
Lucent Technologies Representative or local Authorized Dealer.

6-24

Troubleshooting

«
...
317
318
319
320
321
...
»

Содержание PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PARTNER Advanced Communications System Release 1.0

Бренд: Yealink Страницы: 8

Бренд: GSK Страницы: 32

digital slim -1400

Бренд: Fisher Страницы: 20

Бренд: Albrecht Страницы: 52

SB3.0-1SP-US-40

Бренд: SMA Страницы: 7

Бренд: Lightspeed Страницы: 31

Бренд: Samcen Страницы: 44

Бренд: Audiovox Страницы: 2

Stealthbox SB-GM-4GSUVCNSL/10TW1

Бренд: JL Audio Страницы: 7

Бренд: Sonoro Страницы: 336

Бренд: Jacuzzi Страницы: 28

Бренд: JBL Страницы: 2

Бренд: Work Pro Страницы: 12

Бренд: RF SOLUTIONS Страницы: 8

Stealthbox SB-D-5GRAMCCR/10TW3

Бренд: JL Audio Страницы: 6

Бренд: AEG Страницы: 58

Бренд: AEG Страницы: 66

Бренд: AEG Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды