Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 365

Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 115

Automatic VMS Cover (#310)

Description

This feature applies only if you have a voice messaging system.

This System Programming procedure automatically routes an extension’s
unanswered intercom and transferred calls to the Call Answer Service of the
voice messaging system after a specified number of rings (default for all system
extensions is three rings), so callers can leave a message.

Related Features

To manually change an extension’s VMS Cover state, users can program the

feature on a button with lights. Users can then press the VMS

Cover button to activate the feature (green light on) or deactivate the feature
(green light off). (If Automatic VMS Cover is Assigned at an extension, the
green light is lit

automatically after programming the VMS Cover button to

indicate that VMS Cover is currently active. If this is the case, and the VMS
Cover button is pressed, the feature is deactivated. To activate VMS Cover
again, you must press the button.)

Automatic VMS Cover also applies to outside calls on lines assigned
ownership with

Line Coverage Extension (#208)

VMS Cover Rings (#117)

to change the number of times intercom and

transferred calls or outside calls on lines assigned ownership ring at all
system extensions before they are sent to the voice messaging system.

Users with Automatic VMS Cover turned on can activate Do Not Disturb to

Send All Calls

immediately to their voice mailbox.

If an extension has Automatic VMS Cover and

Call Forwarding

active, calls

ring at the forwarding destination; they are not covered by the voice
messaging system.

Considerations

Standard phones and system phones without a programmed VMS Cover button
cannot override this feature once it is assigned to an extension.

Valid Entries

1 = Assigned
2 = Not Assigned

✔

5-22

Automatic VMS Cover (#310)

«
...
113
114
115
116
117
...
»

Содержание PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды