manualshive.com logo in svg

Lucent Technologies J85501E-1, Руководство по эксплуатации продукта, Страница: 18 / 95

Поделиться
Скачать
Lucent Technologies J85501E-1 Скачать руководство пользователя страница 18

Lucent Technologies Lineage

®

 2000 ECS-6U Controller J85501E-1

Issue 4  August 1998 

Product Description  2 - 5

Basic 
Controller

The basic ECS-6U controller monitors and controls any 
combination of up to six Lucent Technologies switchmode or 
Lineage

®

 2000 ferroresonant rectifiers and provides a single 

interface point for power alarm and status reporting. Equipped 
with a 113A2 Control Unit, a RIB, and a Fuse Alarm Board, the 
basic controller performs traditional analog control functions. 
Each of these functions is described in detail in the paragraphs 
that follow.

Operating

Voltage

The controller is powered by the plant dc voltage and may be 
used in 24V or 48V plants. It may be powered from either 
positive ground systems, e.g., -48V, or negative ground systems, 
e.g., +24V. Movable jumpers located on the upper tray 
backplane and DIP switches located on the 113A2 and the 
Rectifier Interface Board (RIB) must be positioned according to 
the plant voltage. The 113A2 may be plugged directly into the 
ECS-6U controller when the backplane is properly configured. 

Batteryless

Operation

The ECS-6U controller is suitable for telecommunications 
power plants with or without batteries. In batteryless plants, the 
loss of ac power causes an immediate loss of dc power to the 
controller. When ac power is restored, the ECS-6U controller, in 
an unpowered state, allows the rectifiers to automatically restart.

IMPORTANT

When the controller loses power, it also loses the ability to 
detect alarm conditions in the plant. To prevent the danger 
of unreported alarms, Power Major and Power Minor 
alarms are automatically issued when the controller is 
powered down.

IMPORTANT

Not all rectifiers will perform properly without a battery. 
Consult your rectifier manual.

Rectifier Sense

Leads

Separately fused sense leads run from the fuse alarm board to the 
rectifiers via the controller backplane. These leads are not 
interrupted when the 113A2 is removed. The rectifiers use the 
sense leads to maintain the plant bus voltage independently of 
any load-dependent voltage drop between their output terminals 
and the bus.

Содержание J85501E-1
































































































Отзывы:

Нет отзывов