7100 or 9000 Series
Knuckle Assembly
6.0" Mi
n.
Cut Steel Tubing
2Pl. Holes for CKLC100CRT71 Mount
2Pcs. #10-24 x 2"
Socket Cap Screws
2Pcs. #10-24 Nylock Nuts
Make sure the mounting plate is
level when marking both sides
of the tubing to be drilled.
CKLC100CRT71 INSTALLATION INSTRUCTIONS
CKLC100CRT71_Ins - 3/30/09 - M.R.B. ©2009 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
Pr
o
te
c
te
d
u
n
d
e
r o
n
e
o
r m
o
re
o
f t
h
e
se
U
.S
. P
a
te
n
t n
um
b
e
rs:
3,
291,
432 3,
559,
942 3,
724
,798 D
ES
.270,
689 4,
613,
109
4,
878,
645 4
,852,
842 D
ES
.309,
5624,
973,
023 5,
169,
114
5,
255,
884 5,
310,
152 5,
522
,5
76 5,
621,
61
4 R
e
.35,
677 D
ES
.398,
834 5,
826,
384 5,
941
,492 5,
964,
06
8 6,
060,
661
6,
102,
398 6,
158,
704 6,
454,
11
6B
1 6,
761,
276B
2 6,
806,
425B
1
CKLC100CRT71
12 ...
12 ...
12 ...
36 ...
18 ...
4mm Hex Nuts
5mm Hex Nuts
6mm Hex Nuts
5mm Flat Washers
1/4" Flat Washers
2 ...
2 ...
6 ...
6 ...
6 ...
6 ...
6 ...
6 ...
1 ...
1 ...
1 ...
1 ...
2 ...
1/4" Belleville Washer
5/16" Belleville Washer
5/16" Flat Washer
5/16-18 Nylock Nut
4 ...
5 ...
2 ...
2 ...
5/16-18 x 2-1/4" Hex Bolt
5/16-18 x 1-1/2" Button Head Screw
1/4-20 x 1-1/2" Button Head Screw
1/4-20 Nylock Nut
1/4" Flat Washer
Assembly Hardware
Hardware Kit
#10-24 x 2" Socket Cap Head Screws
#10-24 Nylock Nuts
4mm x 25mm Set Screws
5mm x 30mm Set Screws
6mm x 30mm Set Screws
4mm x 12mm Phillips Screws
5mm x 12mm Phillips Screws
6mm x 12mm Phillips Screws
1. Remove the CRT TV from the 7100 or 9000 series mount by unlocking the
TV mounting plate and lifting the TV and mounting plate off of the mount.
2. Remove the knuckle from the tubing using a tubing cutter to cut the tubing
behind the knuckle. The minimum distance from the wall arm, or the bend in
the 9000 series ceiling mount tubing, to the end of the cut tubing should be 6".
3. If the tubing is to be left intact, the knuckle will need to be removed by
taking off a 3/8" Hex Bolt and a hardened Roll Pin. The Roll Pin can only be
removed by grinding in an enironment where the metal grindings won't
cause a hazard. Cutting the tubing behind the knuckle is the prefered
method for installation.
4. Use the CKLC100CRT71 with a level to mark the two holes needed in the
cut tubing. Mark the holes on both sides of the tubing with the mount
held level.
5. Drill 1/4" holes through the tubing in all four marked locations. The holes
on the right side can be made a little larger to adjust the mount level.
Page 1 of 2
