105
Learning Basic Features
4.6.4 RS-485 Communication as a Command Input Device
Internal RS-485 communication can be selected as a command input device by setting
DRV-
06 (command source) in the Drive group to ‗3 (Int 485)‘. This configuration uses upper
level controllers such as PCs or PLCs to control the inverter by transmitting and receiving
signals via the S+, S-, and RS-485 signal input terminals at the terminal block. For more
details, refer to 7
Group Code Name
LCD Display
Parameter
Setting
Setting Range Unit
DRV
06
Command source
Cmd Source
3
Int 485
0
–5
-
COM
01
Integrated
communication
inverter ID
Int485 St ID
1
1
–
MaxComID*
-
02
Integrated
communication
protocol
Int485 Proto
0
ModBus
RTU
0
–6
-
03
Integrated
communication
speed
Int485 BaudR
3
9600
bps
0
–8
-
04
Integrated
communication
frame setup
Int485 Mode
0
D8 / PN
/ S1
0
–3
-
*If AP1-40 is set to
‗4(Serve Drv)‘, MaxComID is ‗8‘, and if COM-02 is set to ‗4(BACnet),
MaxComID is
‗127‘. Otherwise MaxComID is ‗250‘
4.7 Forward or Reverse Run Prevention
The rotation direction of motors can be configured to prevent motors to only run in one
direction. Pressing the [REV] key on the keypad when direction prevention is configured,
will cause the motor to decelerate to 0 Hz and stop. The inverter will remain on.
Grou
p
Cod
e
Name
LCD Display
Parameter
Setting
Setting
Range
Unit
ADV 09
Run prevention
options
Run Prevent
0
None
0
–2
-
1
Forward
Prev
2
Reverse
Содержание H100
