LOYTEC L-IP Скачать руководство пользователя страница 23

Страница: 23 / 173

L-IP User Manual

LOYTEC

Version 6.1

LOYTEC electronics GmbH

Finally navigate to

Save and reboot

and press.

Acknowledge the reboot and the device reboots with the new IP address.

To Register with a Configuration Server

On the LCD main screen navigate to the address field next to CS and click on it.

This leads to the

CEA-709 over IP

menu. Navigate to the

Config Server IP

and enter

the IP address into the four fields. Optionally adapt

Config Server Port

If the channel requires MD5 authentication, set MD5 to ON and enter the secret key
below.

Finally navigate to the bottom, click

Save

and acknowledge with

YES

. The device now

tries to register with the configuration server. Observe the status information to see, if
the registration completes.

Back in the home screen the configuration server is shown with a checkmark.

3.3 Configuration Server Settings

If the L-IP should also act as the configuration server for the IP-852 channel, open the Web
interface and go to the menu

CEA-852 Server

. In the drop-down box

Config server status

select

enabled

and click on

Save Settings

to activate the configuration server. Then the

configuration server settings page shows all settings.

Содержание L-IP














































































































































































Результаты поиска

Содержание L-IP

Отзывы:

LOYTEC L-IP, Руководства пользователя, Страница: 23 / 173

Результаты поиска

Содержание L-IP

Отзывы: