Lowenstein Medical elisa 300 Скачать руководство пользователя страница 444

Страница: 444 / 457

Instructions for Use Supplement F – elisa@megs

Rev. 03

Electromagnetic compatibility:

elisa@megs is only intended for use in an electromagnetic environment in which

radiated RF disturbances are controlled. The user of elisa@megs can contribute

towards avoiding electromagnetic interference by maintaining the minimum dis-

tance between portable and mobile high frequency communications equipment

(transmitter) and elisa@megs.

Warning

Using other electrical devices with elisa@megs or in its vicinity

can cause interference. The correct performance of elisa@megs

must be verified after putting the system into service.

Note

All the elisa@megs features are fully functional if the place of use

meets the EMC requirements set forth in the applicable regula-

tions. Detailed information on electromagnetic compatibility can

be found in chapter 7.3 Guidance and manufacturer's declaration.

3.1.1

Safety standards

The device elisa@megs was developed and manufactured according to the fol-

lowing safety standards:

EN 60601-1

Medical electrical equipment – General requirements for basic safety and essen-

tial performance

EN 60601-1-2

Medical electrical equipment – General requirements for basic safety and essen-

tial performance – Collateral standard: Electromagnetic compatibility – Require-

ments and testing

When applying a ventilator and a terminal device on a patient for medical purpos-

es, you are required to observe the following notes and warnings.

Note

The communication only takes place between one interface and a

single terminal device.

Note

After the initial installation, perform a functional test by checking

whether the communication link between the ventilator and the

terminal device meets the requirements of your facility. Perform

a functional test every time a communication component is re-

placed or modified.

Содержание elisa 300










































































































































































































































































































































































































































































Результаты поиска

Содержание elisa 300

Отзывы:

Lowenstein Medical elisa 300, Инструкция по эксплуатации, Страница: 444 / 457

Результаты поиска

Содержание elisa 300

Отзывы: