Lovibond Maxi Direct Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 268

Lovibond Maxi Direct Скачать руководство пользователя страница 91

89

MaxiDirect_2c 03/2010

1.1 Methods

Notes:

1. To optimise the readings an optional batch related calibration can be performed using
  Mode 40, see page 232.
2. Strong alkaline or acidic water samples must be adjusted to a pH-value between
  pH 4 and 10 before the tablets are added (use 1 mol/l Hydrochloride acid resp.
  1 mol/l Sodium hydroxide).
3. For accurate test results exactly 10 ml of water sample must be taken for the test.
4. This method was developed from a volumetric procedure for the determination of
  Calcium Hardness. Due to undefined conditions, the deviations from the standardised
  method may be greater.
5. The tolerance of the method is increasing with higher concentrations. When diluting
  samples, this should be taken in account, always measuring in the first third of the
  range.
6. Interferences:

• Magnesium hardness up to 200 mg/l CaCO

3

does not interfere.

• Iron concentration above 10 mg/l may cause low results.

• Zinc concentration above 5 mg/l may cause high results.

7. CaCO

3

    °dH
    °eH
    °fH

°aH

«
...
89
90
91
92
93
...
»

Содержание Maxi Direct













































































































































































































































































Отзывы:

Нет отзывов