Lovibond Maxi Direct Скачать руководство пользователя страница 70

Страница: 70 / 268

MaxiDirect_2c 03/2010

1.1 Methods

Colour, true and apparent

(APHA Platinum-Cobalt

Standard Method)

0 – 500 Pt-Co units (mg/l Pt)

Sample preparation (Note 4):

Step A

Filter approx.

50 ml deionised water

through a membrane

filter with a pore width of 0.45 μm.

Discard the filtrate. Filter another

50 ml deionised water

and keep it for zeroing.

Step B

Filter approx.

50 ml water sample

using the same filter.

Keep this filtrate for sample measurement.

1. Fill a clean vial (24 mm Ø) with

10 ml of the filtrated

deionised water

(from Step A), close tightly with the

cap.

2. Place the vial in the sample chamber making sure that

the marks are aligned.

3. Press

ZERO

key.

4. Remove the vial from the sample chamber and empty

it completely.

5. Rinse the vial with the filtrated water sample and fill

with

10 ml filtrated water sample

(from Step B).

6. Place the vial in the sample chamber making sure that

the marks are aligned.

7. Press

TEST

key.

The result is shown in the display in Pt-Co units (mg/l Pt).

prepare Zero
press ZERO

Zero accepted
prepare Test
press TEST

Содержание Maxi Direct













































































































































































































































































Результаты поиска

Содержание Maxi Direct

Отзывы:

Lovibond Maxi Direct, Инструкция по эксплуатации, Страница: 70 / 268

Результаты поиска

Содержание Maxi Direct

Отзывы: