Lovibond Maxi Direct Скачать руководство пользователя страница 58

Страница: 58 / 268

MaxiDirect_2c 03/2010

1.1 Methods

Chlorine dioxide

in the presence of Chlorine

with Tablet

0.05 – 11 mg/l ClO

1. Fill a clean vial (24 mm Ø) with

10 ml of the water

sample

, close tightly with the cap.

2. Place the vial in the sample chamber making sure that

the marks are aligned.

3. Press

ZERO

key.

4. Remove the vial from the sample chamber and

empty it,

leaving a few drops remaining in the vial

5. Add

one DPD No. 1 tablet

straight from the foil and

crush the tablet using a clean stirring rod.

Fill a second clean vial with 10 ml of the water

sample.

7. Add

one GLYCINE tablet

straight from the foil and

crush the tablet using a clean stirring rod.

8. Close the vial tightly with the cap and swirl several times

until the tablet is dissolved.

Transfer the contents of the second vial into the

prepared vial.

10. Close the vial tightly with the cap and swirl several times

until the tablet is dissolved.

11. Place the vial in the sample chamber making sure that

the marks are aligned.

12. Press

TEST

key.

Zero accepted
prepare T1
press TEST

prepare Zero
press ZERO

Содержание Maxi Direct













































































































































































































































































Результаты поиска

Содержание Maxi Direct

Отзывы:

Lovibond Maxi Direct, Инструкция по эксплуатации, Страница: 58 / 268

Результаты поиска

Содержание Maxi Direct

Отзывы: