manualshive.com logo in svg

Lovibond Maxi Direct, Инструкция по эксплуатации, Страница: 264 / 268

Поделиться
Скачать
Lovibond Maxi Direct Скачать руководство пользователя страница 264

262

MaxiDirect_2c   03/2010

Display                

Possible Causes

Elimination

???

 
Example 1

0,60 mg/l  free Cl
???           comb Cl
0,59 mg/l  total Cl

 
Example 2

Underrange
???           comb Cl
1,59 mg/l total Cl

 
Example 3

0,60 mg/l  free Cl
???         comb Cl
Overrange

The calculation of a value 
(e.g. combined Chlorine) is 
not possible

Test procedure correct? 
If not – repeat test 

Example 1:
The readings for free and total 
Chlorine are different, but 
considering the tolerances of 
each reading they are the same. 
For this reason the combined 
Chlorine is most likely zero.

Example 2:
The reading for free Chlorine 
is under the detection limit. 
The instrument is not able 
to calculate the combined 
Chlorine. In this case the 
combined Chlorine is most likely 
the same as the total Chlorine.

Example 3:
The reading for total Chlorine 
is exceeding the range. 
The instrument is not able 
to calculate the combined 
Chlorine. The test should be 
repeated with a diluted sample.

Error absorbance 
e.g.: T2>T1

Fluoride calibration was not 
correct

Repeat calibration

Содержание Maxi Direct













































































































































































































































































Отзывы:

Нет отзывов