Lovibond Maxi Direct Скачать руководство пользователя страница 253

Страница: 253 / 268

251

MaxiDirect_2c 03/2010

Initialise User Method System (Polynomials & Concentration)

Power loss will cause incoherent data. The user method system must be initialised with this
mode function to set it to a predefined state.

ATTENTION:

All stored user methods (polynomial & concentration) are deleted with initialisation.

Press [MODE], [Shift] + [6][9] keys.

Confirm with [ ] key.

The display shows:

Confirm with [ ] key.

The query is displayed:

• Press [Shift] + [1] keys to start initialisation.

• Press [Shift] + [0] keys to to cancel without initialisation.

The instrument goes back to mode menu automatically.

<User m. init>
Start:

Initialising?
YES: 1, NO: 0

Mode

Содержание Maxi Direct













































































































































































































































































Результаты поиска

Содержание Maxi Direct

Отзывы:

Lovibond Maxi Direct, Инструкция по эксплуатации, Страница: 253 / 268

Результаты поиска

Содержание Maxi Direct

Отзывы: