Lovibond Maxi Direct Скачать руководство пользователя страница 235 | Manualshive

Страница: 235 / 268

Lovibond Maxi Direct Скачать руководство пользователя страница 235

233

MaxiDirect_2c 03/2010

After the reaction period is finished proceed as

follows:

9. Rinse the vial (24 mm Ø) with the coloured sample from

the beaker and fill with 10 ml of the sample.

10. Press

TEST

key.

The batch related method blank is saved.

Press [ ] key,
to go back to mode menu.

Notes:

1. If a new batch of CALCIO tablets is used a calibration of the method blank has to be
  performed to optimise the results.
2. Deionised or tap water
3. If no water free of Calcium is available these ions can be masked by using EDTA.
  Preparation: Add 50 mg (a spatula-tipful) EDTA to 100 ml water and dissolve.
4. To achieve the most accurate method blank it is important to adhere exactly to the
  sample volume of 100 ml.

Calcium Hardness Method 191 –
Reset method blank to factory calibration

Press [MODE], [Shift] + [4] [0] keys.

Confirm with [ ] key.

The display shows:

Press [Shift] + [2] keys.

The display shows:

<Calibration>
M191 Calcium Hardness 2T
Reset ?
YES: 1, NO: 0

<Calibration>
  1: M191 Ca-Hardness 2
  2: M191 0 Jus. Reset
  3: M170 Fluoride L

prepare TEST
press TEST

stored

Mode

0

4

2

«
...
233
234
235
236
237
...
»

Содержание Maxi Direct













































































































































































































































































Отзывы:

Нет отзывов