manualshive.com logo in svg

Lovibond Maxi Direct, Инструкция по эксплуатации, Страница: 203 / 268

Поделиться
Скачать
Lovibond Maxi Direct Скачать руководство пользователя страница 203

201

MaxiDirect_2c   03/2010

1.2.2 Cleaning of vials and accessories for analysis

Vials, caps and stirring rods should be cleaned thoroughly 

after each analysis

 to prevent 

interferences.

Procedure:

Clean vials and accessories after each analysis as soon as possible.

a.  Clean vials and accessories with laboratory detergent 

 

 

(e.g.  Extran

®

  MA  02  (neutral,  phosphatic),  Extran

®

  MA  03  (alkaline,  phosphate-free)  

 

from Merck KGaA).

b.  Rinse thoroughly with tap water.
c.  On demand (see Notes) perform special cleaning as required, e.g.: rinse with diluted  
 

Hydrochloric acid solution.

d.  Rinse thoroughly with deionised water.

1.2.3 Guidelines for photometric measurements

1.  Vials, caps and stirring rods should be cleaned thoroughly after each analysis to prevent 
 

interferences. Even minor reagent residues can cause errors in the test result.

2.  The outside of the vial must be clean and dry before starting the analysis. Clean the 
 

outside of the vials with a towel. Fingerprints or other marks will be removed.

3.  If there is no defined vial for the blank, the zeroing and the test must be carried out with 
 

the same vial as there may be slight differences in optical performance between vials.

4.  The vials must be positioned in the sample chamber for zeroing and test with the   mark  
 

on the vial aligned with the   mark on the instrument.

Correct position of the vial (Ø 24 mm):

Содержание Maxi Direct













































































































































































































































































Отзывы:

Нет отзывов