Lovibond Maxi Direct Скачать руководство пользователя страница 156

Страница: 156 / 268

154

MaxiDirect_2c 03/2010

1.1 Methods

Phosphate 1, ortho

with Vacu-vials

K-8503

(see Notes)

5 – 40 mg/l PO

Insert the adapter for 13 mm Ø vials.

1. Place the blank in the sample chamber. The blank is part

of the test kit.

2. Press

ZERO

key.

3. Remove the blank from the sample chamber.

4. Fill the sample container to the 25 ml mark with the water

sample.

5. Place one Vacu-vial

in the sample container. Snap the

tip by pressing the vial against the side of the sample
container.

The Vacu-vial

breaks at the neck and the vial fills au-

tomatically.

A small volume of inert gas remains in the Vacu-vial

6. Mix the contents of the Vacu-vial

by inverting it several

times, allowing the bubble to move from one end to
the other. Dry the outside of the vial.

7. Place the Vacu-vial

in the sample chamber.

8. Press

TEST

key.

Wait for a

reaction period of 5 minutes

After the reaction period is finished the measurement
starts automatically.

The result is shown in the display in mg/l ortho-
Phosphate.

Countdown
5:00

prepare Zero
press ZERO

Zero accepted
prepare Test
press TEST

Содержание Maxi Direct













































































































































































































































































Результаты поиска

Содержание Maxi Direct

Отзывы:

Lovibond Maxi Direct, Инструкция по эксплуатации, Страница: 156 / 268

Результаты поиска

Содержание Maxi Direct

Отзывы: