Lovibond Maxi Direct Скачать руководство пользователя страница 152

Страница: 152 / 268

150

MaxiDirect_2c 03/2010

1.1 Methods

Phosphate, ortho

with Vario Powder Pack

0.06 – 2.5 mg/l PO

1. Fill a clean vial (24 mm Ø) with

10 ml of the water

sample

, close tightly with the cap.

2. Place the vial in the sample chamber making sure that

the marks are aligned.

3. Press

ZERO

key.

4. Remove the vial from the sample chamber.

5. Add the contents of

VARIO Phosphate Rgt. F10 Powder

Pack

straight from the foil to the water sample.

6. Close the vial tightly with the cap and swirl several times

to mix the contents (approx. 10-15 sec., Note 1).

7. Place the vial in the sample chamber making sure that

the marks are aligned.

8. Press

TEST

key.

Wait for a

reaction period of 2 minutes

After the reaction period is finished the measurement
starts automatically.

The result is shown in the display in mg/l ortho-
Phosphate.

prepare Zero
press ZERO

Zero accepted
prepare Test
press TEST

Countdown
2:00

Содержание Maxi Direct













































































































































































































































































Результаты поиска

Содержание Maxi Direct

Отзывы:

Lovibond Maxi Direct, Инструкция по эксплуатации, Страница: 152 / 268

Результаты поиска

Содержание Maxi Direct

Отзывы: