Lovibond Maxi Direct Скачать руководство пользователя страница 140

Страница: 140 / 268

138

MaxiDirect_2c 03/2010

1.1 Methods

Ozone,

in the presence of Chlorine

with Tablet

0.02 – 2 mg/l O

1. Fill a clean vial (24 mm Ø) with

10 ml of the water

sample

, close tightly with the cap.

2. Place the vial in the sample chamber making sure that

the marks are aligned.

3. Press

ZERO

key.

4. Remove the vial from the sample chamber and

empty it,

leaving a few drops remaining in the vial

5. Add

one DPD No. 1 tablet

and

one DPD No. 3 tablet

straight from the foil and crush the tablets using a clean

stirring rod.

6. Add water sample to the 10 ml mark.

7. Close the vial tightly with the cap and swirl several times

until the tablets are dissolved.

8. Place the vial in the sample chamber making sure that

the marks are aligned.

9. Press

TEST

key.

Wait for a

reaction period of 2 minutes

After the reaction period is finished the measurement

starts automatically.

10. Remove the vial from the sample chamber, empty the

vial, rinse vial and cap several times. Fill the vial with

few drops of the water sample

11. Add

one DPD No. 1 tablet

and

one DPD No. 3 tablet

straight from the foil and crush the tablets using a clean

stirring rod.

prepare Zero
press ZERO

Zero accepted
prepare T1
press TEST

Countdown
2:00

Содержание Maxi Direct













































































































































































































































































Результаты поиска

Содержание Maxi Direct

Отзывы:

Lovibond Maxi Direct, Инструкция по эксплуатации, Страница: 140 / 268

Результаты поиска

Содержание Maxi Direct

Отзывы: